Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

THE BRUSH ISN'T TURNING, EVERYTHING ELSE IS WORKING.


Answers :

Sounds like the beater brush is frozen and won't turn. Remove the beater brush and clean off all debris, especially at both ends. You will find a square(?) piece at each end of the beater brush that holds it in place. This need to turn freely. Put a little WD40 on these where the center rod of the beater brush enters the small holders and turn by hand until they turn freely. Once this is done, assemble with new belt, making sure the belt is put on properly.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.


Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Brush will not turn but everything else works ok


Most uprights use a small belt that drives the carpet brush. if you have the manual for it usually it'll show what type or size belt is needed for replacement, as well as the procedure for replacing the belt.\015\012Hope this helps! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

THE BRUSH ISN'T TURNING, EVERYTHING ELSE IS WORKING.


Sounds like the beater brush is frozen and won't turn. Remove the beater brush and clean off all debris, especially at both ends. You will find a square(?) piece at each end of the beater brush that holds it in place. This need to turn freely. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Hampton Bay ceiling fan St. Regis model #138 498. Somehow the remote got messed up and now the lower light flashes on/off when the power is on and nothing else works. This happened one other time and I simply turned off the switches and when they were turned back on everything worked fine. This fix does not work this time.


... Vacuums

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dyson dc14 brush bar is not turning at all. Everything else seems to be fine. I just replaced the brush bar but still no movement. What else could it be?


Hi there,I'm sorry to hear you're having difficulty with your DC14 Animal. If the brushbar doesn't rotate, please check you have the brush control set to 'Carpets', not 'Hard floors'. The brushbar will not rotate when the machine is standing ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.


That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?


Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I have a hoover steam vac f5899-100 the brushes doesnt spin...everything else works but tha. we took the brushes apart to clean


There is no belt it is air the gears stick open it up and spin them free ... Hoover F5899-910 SteamVac Vacuum

Dyson DC14 roller doesn't turn but everything else works. The belt is on correctly, the roller is clean and it turns manually so I can't figure out the problem.


The DC14 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" and "carpet". The roller will turn only when the knob is on "carpet", and even then only when the handle is tilted back ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

MY DYSON YELLOW BALL EVERYTHING IS WORKING EXCEPT THE BRUSH BAR DOSN'T TURN EVERYTHING BEEN CLEANED ? WWHAT CAN I DO ?


I'm not a vacuum cleaner expert, but I suspect that the rubber drive belt is broken (if it uses one) ... Vacuums

My front spin brush stopped working but everything else works


You will need to replace the belt. Remove the screws from the bottom of the unit. Then remove the brush roller. You should be able to see the belt, if not you'll need to look on the upright part of the unit and ge tthe belt's "code" usually a letter. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?


The brush is worn out most likely ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have the Hoover Deluxe Elite Rewind with the 24 ft cord reel. I can't seem to find the instructions or a model # exactly for it. The vacuum is just over a month old but when I turn it on now it's not sucking at the bottom and the hose and everything else appears to be attached so I don't know why it's not working.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=572145\015\012Generic problem for all Vacuums\015\012I have the Hoover Deluxe\015\012Posted by y2kas32 on May 05 ... Vacuums

Kenmore Beltless Vacuum brush will not spin. Everything else works.


There is a reset button on the side of the lower base of the machine, plug in the unit turn on the switch to the brush and vacuum are both engaged hit the reset button, remember the roller will not engage when the handle is in the upright position, r ... Vacuums

My model # DBL-2000-MS heat will not come on,and as you turn up the thermostate it shuts off right at the point when it should be at highest temperature but the heater element never comes on. Everything else works.


... Vacuums

The brush does not spin when engaged. Everything else is working fine.


When you remove the brush, the release button resets a trip fuse on the pcb. If that does not work at sounds like you have either blown the rectifier pcb or burnt out the DC motor that is in the brush head. You can get a complete replacement brush he ... Dyson Ball DC24 Bagless Upright Vacuum

Hoover steamvac brushes don't spin. everything else works great. Took it apart and no visible problems


My husband took it apart today and the impellers were gunked up with black stuff. \015\012\015\012he used these pictures that someone else generously posted. ours was slightly different in internal design, but they are helpful regardless ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dyson dc14 animal is falling apart! The canister keeps falling our and now the carpet/floor adjuster doesn't work AND the brush wont turn....tried everything. I live in Half Moon Bay, CA (near San Francisco) where can I bring it to be OVERHAULED? Thanks


The best sol would be to search for vacuum repair half moon bay, ca. To see if there is a vac shop near you. my suggestion's would be either Vacuum Cleaner Shop #(877) 822-8227 or Vacuum solotions #(502) 348-4900. hope this helps ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a kenmore vacuum and the head of the vacuum is not turning as it should..what do i do? Everything else seems to be working...I tried to reset it but nothing happened. One more thing what is the head of the vacuum properly called?


Replace the belt on the vaccum. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0746 seconds