Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Beater roller does not turn but belt is connected to bottom roller

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater roller does not turn but belt is connected to bottom roller

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When I engage the beater roller it will work for a short time (15-20 seconds) and then squeel loudly as if something is not engaging properly. I checked the roller ends and cleaned them but it seems to roll freely by hand while connected to the belt and then at a time it becomes very hard to turn by hand.

Sounds to me that the motor is shot. There is a main bearing the belt shaft connects to and it sounds like the bearing is seazing and gets worse when it nheats up. Soon it wont turn anymore at all ,once it siezes completely. These are rarely worth f ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

My hoover upright u8172-900. The unit provides suction, but roller does not turn. I can hear the motor click on when it is supposed to. I took the cover off, and found no belt. Does this one operate without a belt, or is it possible the belt was totally obliterated? I saw no place to connect a belt, but I didn't want to do too much disassembly at this time.

You need to replace your belt when belts get old they snap into and sometime or sucked up into your bag ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I have an Oreck canister vacuum, it says fc1000 on the bottom sticker, it's red. My problem is that the suction in it works perfectly, the belt is ok, and the roller can turn, but the motor doesnt turn it when I turn on the power.

... Vacuums

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........

Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port. ... Hoover Tempo Widepath Upright Vacuum - Blue

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy

The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Halo beater bar has quit working. bar (that belt is wrapped around) connected to motor is not turning. have pushed reset button. k.r.

Take it to an oreck dealer. duh ... Vacuums

It makes a loud noise when turned on. it doesn't make the noise when you use the hose. It looks like the roller on bottom is cracked where the belt wraps around it.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Model DC14 beater brush doesn't turn. belt from motor turns but doesn't turn beater brush belt from clutch . Is clutch bad??

You might need to replace both belts. You can get them here:DC14 Replacement Belts ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down

... Eureka Vacuums

Ratchet noise, beater will not turn, belt not broken, in carpet mode the Dyson d07 makes huge ratchet noise and the belt will not turn the beater brush.

Ok, so I had the same ratching noise and took the advice of many sites directing me to clean the brush. But like most I cleaned the brush and the noise continues and the brush does not spin. Reluctant to take it to get serviced I dug a l ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?

Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]

Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.

Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My Hoover Platinum LiNX Cordless Stick Vacuum beater bar is not turning. After removing some clogged hair and items...the vacuum cleaner has suction, but the beater bar will not turn. What to do? The belt is still attached and will turn manually.

... Hoover Platinum LiNX Cordless Stick Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn

The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0836 seconds