Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Brush does not touch floor when handle > 45 degrees

\015 When the handle is greater than 45 degrees from upright, the rotating brush does not touch the floor and vacuum performance is greatly reduced. It seems like there should be a spring or something to cause the brush unit to move toward the floor.\015

Answers :

\015\012I have come accross this a few times over the years,
\015\012I have found that the only way to rectify this is to fit new internal hose (short transparant hose under machine)
\015\012When a new one is fitted the spring coil action from the hose pushes head flat down to floor.
\015\012Hope this helps you.
\015\012 http://dysonmanuals.llc.nu/
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush does not touch floor when handle > 45 degrees

Hi.\015\012\015\012I have come accross this a few times over the years,\015\012I have found that the only way to rectify this is to fit new internal hose (short transparant hose under machine)\015\012When a new one is fitted t ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.

Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

No matter how many new belts we put in the brush will not rotate when it touches the floor. If you hold it straight up the brush rotates like crazy. Why is the brush not cleaning the floor. Yes, I have the right belt. It is R we have the boss. 12 amps. Model 4870

There is probably an accumulation of slippery stuff on the shaft that drives the belt. You can scrape it clean with a sharp knife or a razor blade. You might need to use some kind of solvent to get it clean, and if you do, be sure to follow up wit ... Eureka Vacuums

Handle no longer 'locks' causing the attachment suction to engage when I'm using the floor brush.

... Dyson DC25 All Floors Bagless Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

The brush is not touching the floor - the front plate is rubbing.

Dear there is clear problem in the adjustmen of brush hair.and i see that you must have to try to b correct it..\015\012and also i see that u must have to see that there is rubber inside it and try to see whethe ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Loose handle on shark v1950 sweeper - Shark Euro-Pro V1950 VX3 Rechargeable Stick Broom Sweeper, 13" Motorized Brush Roll, Folding Handle, 2 Speeds, 50 Min Cleaning, Carpets & Floors

... Shark Euro-Pro V1950 VX3 Rechargeable Stick Broom Sweeper, 13" Motorized Brush Roll, Folding Handle, 2 Speeds, 50 Min Cleaning, Carpets & Floors

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.

... Eureka Vacuums

Eureka Smart Vac Brush not rotating when touching floor

Sounds like either the belt wasn't routed correctly or the idler clamp asm.(part # 704194CSV) has a problem. There should be a diagram showing the belt placement either by the belt or on the inside of the cover. ... Vacuums

Brush does not turn when vac touches floor

You need to change the belt. The belt will not turn the brush roll and is slipping on the drive shaft. This is creating the burning smell you describe.\015\012You say you just brought it home.From where? From repair or is this a new machine. ... Vacuums

I have a Bissell Proheat model 7901. When I pull the trigger on the handle, there is no water flow. The brushe revolves and the unit vacuums any water spilled on the floor. Could it be a failed pump or kink hose or ? Thanks Zap

Take the handle apart and put spring back into place. ... Bissell Vacuums


Can you hear the motor for the brush turning. it sounds like the belt will need to be replaced. ... Vacuums

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.

The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dyson DC17 makes a loud noise when i tip the handle down to make the brush spin on the floor?

Loud noises are usually caused by worn belts, unbalanced roller brush or debris in the roller brush. Check these things. Here is a link to the belt you need: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brush not working when the handle is reclined

Sonds like you have a problem with the self propel switch in the handle. Since you didn't provide a specific model number, I can only give you generic information on what might be the problem.. Here is a link for a hoover upright model ( may or may n ... Hoover Vacuums

The brush won't stop when selecting hard floor

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

I live in Mexico and have a Electrolux Easy Box Vacuum...I am looking for a hard floor brush that will fit the hose as my old Sears brushes are a little too small.This model is bagless and may only be sold here,but I do not care for the floor/rug brush combo brush as it does not clean tile floors very well.I would order and have a friend in the states bring to me.Thank you,Linda Staton Cozumel Mexico

... Electrolux Vacuums

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.

You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net

What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Hoover 6446 900 WindTunnel Bagged Upright has little suction at the floor brush but plenty at hose if disconnected. It does not seem that there is anything blocking the inlet at the floor brush.

Check for a clog in the brush hose ... Hoover Tempo Widepath Upright Vacuum - Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds