Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?
I can't get the roller bar back in
\015 The roller bar was making a loud sound and not sucking up like it should, so i turned it off and flipped it over and the bar had all sorts of stuff tangled around it, so i pulled off all the stuff and the roller bar fell off in the process, now i can't seem to get it back in the way it was. The cover that goes over it won't fit properly and it seems like the bristles are hitting something and won't **** anything up. I also checked for any kind of clog and found nothing.\015
The oval shaped ends of the brushroll have to be rotated to one side and rest on the wall of the brushroll housing, once you line this up your cover should fit on. also make sure to install the brushroll the right way with the belt on the molded ball section of the brushroll. if this is done, nothing should interfere. let me know if you still have trouble
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I can't get the roller bar back in
The oval shaped ends of the brushroll have to be rotated to one side and rest on the wall of the brushroll housing, once you line this up your cover should fit on. also make sure to install the brushroll the right way with the belt on the molded ball ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I cant get the roller back in place
On the ends of the roller turn the ends and you will see some teeth ,the teeth are supposed to be aiming down.if its because of the belt,slip the belt over the roller then put the belt on the motor shaft first and pull the roller towards the front a ... Oreck XLS700A Upright Vacuum
Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!
Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I cant get the belt and roller back on
... Riccar 8955 Upright Vacuum
I took the roller off my cleaner model 8910 and the black pieces came off as well and now I cant get them back on properly
Place the black brush arm onto the brush (the arm has a stand up pin / spigot which needs to be located into the centre of the brush) and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original p ... Bissell 8910 ProHeat Clear View Upright Vacuum
Tried to take roller brush out to clean it's housing, cant get one side back in without trying to force it.
The roller brush fits snug in the housing, however, if you had it out, check to make sure the end caps of the brush shaft are pushed all the way on. These just slide on the roller bar shaft and if something got under them, they would not be able to ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy
The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?
If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and
Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together
Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.
Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums
CANT GET MY POWERSTEAMER PRO DELUXE MODEL 8804 BACK TOGETHER
Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum
I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?
THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum
Cannot get the brush bar back in
This video will show you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
We have already spent $60 on getting the belt repaired once. This time, the same thing is happening, the belt is jumping of the small metal bar in the back of the housing. Seems like there should be something on the end of the bar to keep the belt on it?
Greetings from GoVacuum,\015\012\015\012Ahh, the Hoover Windtunnel Self-Propelled model. This model has a some reoccurring problems with it. The majority of them have to do with the b ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.
... Windsor VS14 Versamatic Bagged Upright Vacuum
Can't get beater bar back on Dyson Animal - it won't set back into the machine correctly.
The bearing blocks must be oriented correctly. Take the belt off and put the brush in place. Once you have it in, mark the surface that is visible with a dot of white out, nail polish or marker, depending on the color of the block. Remove the brus ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]
Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You
Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
I REMOVED THE PLATE THAT IS OVER THE ROLLER TO CLEAN THE ROLLER OF HAIR AND NOW I CAN'T GET THE PLATE BACK ON AND TO SNAP INTO PLACE
If you go to this URL:\015\012\015\012http://media.dyson.com/downloads/us/floorcare/manuals/dc17_opmanual_usa.pdf\015\012\015\012you can see a diagram on how they suggest to take the plate off and clean the unit.\015\012I hope this will o ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do
I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum
I think the motor for the roller bar is going out, it won't turn very fast and we cleaned the bar, and made sure the belt is on right. is this an easy fix or where can I get repaired locally and quickly?
You may have to take out the roller brush completely and check the side bearings for packed in dirt. Clean out as best as you can and make sure it spins freely. use WD40 to lube it up. Hope this helps. ... Kenmore 25512/ 25513 Progressive Canister Vacuum