Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Beater bar not spinning, seems to be stuck but when I manually spin it, it will start but will stop and go.


Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar not spinning, seems to be stuck but when I manually spin it, it will start but will stop and go.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.


I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Dyson DC28 Beater Bar will stop turning then start again. Then it quits all together and after awhile it will start again.


Hi there, it's Jack at Dyson.I'm sorry to hear your DC28's brush bar seems to be working intermittently. It may be worth taking a look at the video I've attached below, as this shows the correct way to check the cleaner head for obstructions ... Dyson DC28 Animal Bagless Upright Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My scooba when switched on starts to spray water then spins round faster than normal then starts to go backwards quite quickly then stops then continues to reverse more then stops & with the nor


... iRobot 5800 Scooba Vacuum

I have a Panasonic Performance plus MC-V5217. Something got stuck in the rollers and it stopped spinning. We've cleared the brushes but can't get it to spin. Is there a reset button?


... Vacuums

My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem


It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half. ... iRobot Roomba 530 Robotic Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.


How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]


Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Took Roomba apart to clean and now the pick up brushes start and stop during cleaning. The vaccum is clean but will not constantly spin. Runs great but pick up brushes start and stop. Is there a number for Roomba? Warranty? This one is less than one year old.


You can go to www.iRobot.com . This is the roomba website. You should be able to find replacement parts, customer support, videos or the Roomba product, and more.\015\012When y ... iRobot Roomba 530 Robotic Vacuum

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

The spin brush stopped working on my bissell proheat turbo. But they will start to spin when i shut it down and the motor has almost come to a stop.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

The brush bar on my brand new DC 28 has stopped spinning - it is not clogged with hair, it just stops spinning almost immediately. Is there a reset button?


If there is nothing dragging it down like clogged hair ect then usually this just means the rubber drive belt has either stretched or is too smooth to grip and properlly drive the beater bar brushes. When those happen the belt cannot get a grip and s ... Vacuums

Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.


Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have the Janome 6600 P. Beginning a seam the thread knotted and the machine made noise and needle would not move either up or down. I manually moved the needle using the handwheel and cut away the knotted thread. I began sewing again but instead of starting at the edge began about a half inch down, forward stitched, reversed to lock threads and problem repeated and received the message to "Stop for safety purposes". Did that. Referred to the manual, tried manual recommendation. Did not work. I


... Vacuums

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.


... Vacuums

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Spinner bar not spinning got something stuck in it


Hi there,I'm sorry to hear you're having difficulties with your DC14. Your cleaner is equipped with a safety device which shuts off the brushbar if it gets tangled with a rug fringe, shoelace etc. After making sure the brushbar is free of ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush bar on my Dyson DC17 stopped turning.


If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds