Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

Dyson DC7 wire gets hot

\015 I noticed my Dyson DC7 wire gets hot when using it, esp. the part\015\012plug into the socket. Do I need to get the wire replaced ?\015

Answers :

Hi.
\015\012
\015\012Definately yes & ASAP.
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson DC7 wire gets hot


Hi.\015\012\015\012Definately yes & ASAP. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.


Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Dyson 07 plug gets very hot after prolonged vacuuming


Electrical current passes through the electric cord and plug - it will get warm, that's normal. If the problem is worse where you smell an electrical burning smell, only an authorized dealer can fit a new power cord to your vacuum cleaner. Call the D ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?


Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off.


This post may be of assistance: http://www.fixya.com/support/t2842769-fix_new_power_cable_dyson_dc07\015\012\015\012Hope it helps ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Dyson DC25 ball gets very hot - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

Dyson dc41 vacuum ball gets hot - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

HOW DO I CHANGE THE MAINS POWER CABLE ON A DYSON DC07? my wife cought the cable under the dyson and has stripped it to bare wires so i need to change the cable. i have taken a cover off near where the cable goes into the machine but now cannot get any further


How to open the cover near the cable for dyson upright vacuum ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

The handle for my Eureka 5893 AVZ was getting very hot. Finally, the wires around the switch melted and the vacuum will not work. What is wrong? Is the switch bad? Nothing else appears to be wrong.


Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. It almost melted the handle! Ordered a switch after talking\015\012to several repair men. Talked to Eureka, too, and they were absolutely\015\012no help. Cheap wiring ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Have a Shark steamer. Tried the vinegar, tried the CLR, tried putting a piece of wire and a skewer into steam hole...no luck. The unit gets hot but no steam. Will try one more round of CLR and let it sit overnight. Other than all that I mentioned...have no idea what to do next. It's a great gadget if it worked!!


\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Dyson dc7 quits after a few minutes running; runs again after an hour or two of rest. Filters are clean, beater bar is clean, can't tell about the airways because I can't see how to get to them.


Check the ducts with a small object(screw or something with a little weight)down the ducts to verify they are clean. Also check the Ubend on the back bottom of the unit. Looks just like a U. Remove with a turn of the tab by a screwdriver or quarter ... Vacuums

Dyson Animal Dc28..no suction...getting hot - Vacuums


Hi there,Sorry to hear you're having difficulties with your DC28. If it doesn't seem to be picking up as well as usual, it's possible that there's a blockage in the system, and you may need to give the filters a wash.The easie ... Vacuums

My dyson animal just cuts out mid vacuming ,the motor gets quiet hot ,and wont start again for an hour or so when i expect the motor cools down .all filters cleaned no blockages etc.. any suggestions?????


This is a feature so that the motor does not burn up check all tubes ... Vacuums

Dyson has lost it's suction...i've cleaned all filters and checked all the hoses. The motor appears to be getting too hot


The filter housing can also be an issue. Check this:\015\012\015\012http://www.ehow.com/how_5870417_modify-dyson-prefilter-suct ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson animal works for a while then shuts off...i guess it's getting hot and automatically turning off to keep damage from occuring. i have cleaned the filter and all the collection basket, but am still ahving problems. it was just services a year ago and a new switch installed. please help!!!


The belt that drives the beater bar may be broken or stretched, causing the motor to turn more freely, therefore causing the motor to rev beyond it's design.Jim ... Vacuums

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc 05 and a wire has come disconnected from the main cable inside the machine how do i get the wheel off to reconnect the cable


In the centre of each wheel there is a different colour plug. This must be removed before the wheel can be pulled off. I used a small screwdriver to prise it out. You will probably damage the plug in removing it but they are easily available online a ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Dyson DC7 full Kit, with one belt does not get suction to head.


I took the pre filter out of my dyson it now sucks wonderfully By the way mine wont **** at all with brand new clean prefilter it mine is a dyson animal .My other dyson is the yellow one that works with prefilter in no onw has been able to make my sc ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

The motor on my Dyson Animal DC07 is getting very hot. I've always kept the filters and such clean. Is there any maintenance I am to be doing with the motor?


Hi its Darran at Dyson.From your description of the problem, it sounds as though there is a lack of airflow to the motor which is caused by a blockage in the machine or a dirty filter. To check your machine for a blockage, ple ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Gets hot, burning smell and turns off - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum


Hi there, Unfortunately you have a burnt out motor I would suggest. Of all common vacuums this is probably the easiest to change if you feel up to a home repair. I have made a video of how to do it and posted it on ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My dyson has started to give off an acrid smell when I use it. I have checked all areas for blockages, cleaned the removable filter and removed all hair from the brush but this has not helped. I am worried the motor is getting hot in use. Whats the best thing to do next? Thanks


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0668 seconds