Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

DC07 Very difficult to push forward.

\015 We have a DC07 which recently has been very difficult and heavy to push forward. When attempting to push forward it appears that the front cleaning head wants to dig into the carpet, and with the suction it is extremely difficult to move. You can pull cleaner backwards ok though. Anyone got any ideas?\015

Answers :

On the front of the base there are 3 very small rollers made out of rubber, these are either just dry and won't turn or worn and or damaged,

that is your problem / honest its that simple
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DC07 Very difficult to push forward.

On the front of the base there are 3 very small rollers made out of rubber, these are either just dry and won't turn or worn and or damaged, that is your problem / honest its that simple ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson is very difficult to push forward. I've made sure the brush is spinning freely. How do I find out what is causing this and fix it? thank you.

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Dyson DC07 is excessively difficult to push. The plate on the bottom was replaced & helped a little bit for a while.

You should probably consider fitting a new brush roll. The bristles gradually wear away, to the point where they no longer help to pull the machine over the carpet. A new brush with full-length bristles will almost certainly solve the problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?

Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush won't rotate when pushed forward

I had the same problem . The reason it acts like that is due to the cable that runs from the vacuum motor to the brush assembly has an intermittent open. My fix was to find the small cable that was causing my troubles and splice it. Making sure that ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

How do i fit forward lock on dyson dc07 - Dyson DC07 Bagless Upright Cyclonic Vacuum

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Greetings - my Dyson DC41 animal vacuum seems to be having problems with the ball - the right side of the ball if you were to be standing behind the machine seems like it's tightening as it rolls forward, as it tightens its harder to push the machine forward. Any thoughts, any fix it ideas? Thank you.

... Vacuums

My eureka central vac power brush turns off when pushing forward than back on when pushing back. Ever seen this before?

Yes I repair them all the time. What that means is that the connection of the hose handle to the power brush upper wand is loose. This can happen over time with use. The connection just loosens up. Do you have the exact model of the power brush? ... Eureka 1810 Central System Vacuum

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do

I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?

Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell Proheat 2x Model 9200. The solution goes directly through to the carpet. The tank empties extremely fast even when I am not pushing the button. I have also noticed that I have soap spots on the carpet when pushing the cleaner forward. These spots are not even associated with the cleaning mechanism. I have inspected the cap on the tank, but it seems to be OK. Any suggestions?

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9200 Upright Vacuum

My hoover widepath tempo pushes easy in any hight when off, but turn in on and you can hardly push in forward. I took the beater bar off and cleaned everything and still having this problem

Make sure the beater bar is turning sometimes it will freeze up with dust and dirt will get inside the bearing caps on the end of the brush ... Vacuums

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor

On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My quite new neumatic henry hoover is really difficult to push - you need all your strength. I do not have the brushes down and its still really hard to push - can anyone advise? thanks

... Henry Numatic "" Canister Vacuum

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

How do i fit forward lock on dyson dc07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I can barely push the vacuum forward and there is noise

Dyson design to help save belt so its not destroyed when brush grabs. its the clutch you \015\012hear very annoying and scary lol .it should move very easily forward almost pull itself in \015\012carpet mode the way the brush rotates, unless ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Every time i push the steam vac forward it dispenses water

You are having the same problem i am and so far the best solution i have found is i need a new clean tank just got my steamvac today bought it cheap so not complaining much the other solution i found was to only have the cleaning solution tank in for ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Sweeper vibrates when pushed forward.

Do u put it on drive or neutral? does the wheels spin when on drive? is the height adjuster on the right level? ... Kirby Ultimate G Bagged Upright Vacuum

Bissel Proheat 2x "catches" when it is pushed forward-- Help Please!!!!

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=618960&thid=499675\015\012Bissell ProHeat 2x "catches" when it is pushed...\015\012Posted by Marlene101 on Apr 08, 2008 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0410 seconds