Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

My dyson sucks good untill i put handle down

\015 My Dyson sucks good until I put the handle down, than it won't suck\015

Answers :

Try moving the floor/carpet selector dial on base of vac back and forth, from floor to carpet repeatedly, at least 5-6 times....it may be stuck
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson sucks good untill i put handle down


Try moving the floor/carpet selector dial on base of vac back and forth, from floor to carpet repeatedly, at least 5-6 times....it may be stuck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson hose sucks good but, when i put handle down, it won't **** but brush does turn


I just had the same problem....suction from wand, but no suction from soleplate, the brush bar spins. Did all the troubleshooting steps on dyson.com but they didn't work...dyson.com says need to take to repairman, being a diyer I went to search engi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson d17 will only stay on if the handle is tilted back and it's not sucking at all....although it's running. When i stand the vacuum up with the handle upright, it cuts off.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor loud I have a dyson dc17..recently when i turned it on and pulled the handle down to vacuum the motor was very loud..put the handle in the upright position it is quiet.any suggestions?


When you put the handle down it turns on the brush roll. you may need to clean the brush roll or replce it if the bearings are bad.also clutch and 2 belts are started when putting handle down for brush operation. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Why doesnt my rootcycle dyson **** up! belt ok, emptied regularly, the handle bit where it sucks is fine but not the rotating brush. it sucks up fluff but not light dirt and bits. changed white pipe underneath as it was split.


There is a removable cover on the bottom of some Dysons which is like a U-Bend. On occasion this is a likely spot for blockages. Also make sure that all of your filters have been cleaned. Locate your local Dyson Customer Service from ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cannot put handle on dyson - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi,Did you receive the handle with the wand already attached? It should be. Then, to get it into the hose pres the wand release button on the end of the hose and slide the wand into the hose. The wand should then be pushed into the slot o ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson ball DC24 when you put the handle in the tube the handle goes toofar and pushes the bottom open


Hi there,I can confirm that what you've noticed is part of the valve mechanism, which switches the airflow from the hose to the cleaner head when you replace the wand on the machine. This is a normal feature of the DC24, and nothing to worry ... Dyson Ball DC24 Bagless Upright Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx


Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?


If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

I removed the handle of my Dyson DC24 to vaccum in high areas and now when i try to put the back piece back, it doesn't click. So when try to vaccum on the floor the handle just comes off.


Hi there,I'm sorry to hear you're having difficulty with your DC24. The wand handle should reattach easily to the machine, locking into place with an audible 'click'. If it doesn't seem to be doing this, you may want to check you have the han ... Dyson Ball DC24 Bagless Upright Vacuum

Putting together the dyson DC25 all floors handle that regulates the switches


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson dc40 sucks from Hose(at the handle) while vacuuming floors


... Dyson Dc40 Multi Floor Lightweight Ball Upright Vacuum Cleaner

My Dyson turns on and is not sucking. It makes a


I have the dyson dc 27. On the bottom left back side of mine there is a circle, and ball inside of it. I turned it on and pushed the ball and it started working again. Sometimes it doesn't cover the whole and stops sucking air through it. ... Dyson DC07i Bagless Upright Vacuum

Not sucking up the dirt...making loud sound when we put the handle down to start vacuuming


The brush needs to be removed and cleaned, also take the sole plate off and check for obstructions. The noise you are hearing is the motor protector doing its job. When the brush does not spin freely the clutch engages and keeps the motor from burnin ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Loud grating/rattling noise comming from dyson dc04 when ever hovering upright as soon as i angle back the handle to push it. the belt has not come off, the roller is rolling and not jammed. sucks ok from the flexible hose.


... Dyson Vacuums

How do I put the dyson handle back together after pulling out to vacuum a small area?


... Dyson Ball DC24 Bagless Upright Vacuum

I have a dyson dc17 animal. When you put the handle down, it is very loud


Hi there,When you lower your DC17's handle into the vacuuming position, a second motor which powers the brushbar will switch on, which will make the machine sound a little louder than when it's standing upright.However, if you're conc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson no longer sucks like it used to. I have to put my hand and add pressure to the front of the vacuum in order for it to pick up hair and lint. What is wrong?


Sounds like it needs a new brush roller. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My dyson dc animal's brush is not spinning. The machine smells like burning rubber. I believe the clutch has gone out but the machine also only sucks from the top of the hose in the handle. I am wondering if the machine is not locking properly which is causing the brush to not need to spin. If this is the problem how do i fix this problem.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?


Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Putting new vacuum together position of the handle


The handle should be attached so that the open portion of the handle is facing towards the brushs( away from user) ... Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

My Dyson 41 has just started only sucking through the tube


We've had our DC41 for 4 months now and suddenly noticed no suction at the base as well. Base motor works fine.Thought I'd take one last look before sending in for repair. At the base of the attachment hose near the motor is a small red tab. I depres ... Dyson Dc 41 Ball

Dyson DC 41 wont suck.


... Dyson Bagless Upright Vacuum DC41 Animal

My dyson DC23 sucked up some plastic bags in the hose. How do I get them out?


... Dyson DC23 Bagless Canister Cyclonic Vacuum

I have a Kirby G4. I have noticed the last few days when trying to vacuum that it is blowing more than it is sucking up. I put on a new bag to make sure it wasn't too full. I also put on the hose and noticed it's not sucking as well as normal. I unzipped the back of the bag holder and noticed the bag isn't inflating as it should be as well. I appreciate any advice. Thank you.


Take the mini emptor off(plastic piece on bottom of cloth bag) this is done by rotating it away from the body of the machine. There is most likely a clog there. Also take the brush head off and inspect fan for chips or cracks this will also reduce su ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0513 seconds