Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

My dyson hose sucks good but, when i put handle down, it won't **** but brush does turn

\015 Vacuum hose sucks good, between I put handle down it won't suck, brush does turn, but won't suck with handle down\015

Answers :

I just had the same problem....suction from wand, but no suction from soleplate, the brush bar spins. Did all the troubleshooting steps on dyson.com but they didn't work...dyson.com says need to take to repairman, being a diyer I went to search engine.\012\012I didn't find a fix, however I found one myself....it appears the vac can get stuck in floor mode or in between modes....the dial on top on dc07 ....selector of floor or carpet..try pushing it back and forth to see if that puts it in carpet mode...check for suction or try vacuuming...if that doesn't work, looking at vac from behind vac on the right hand side is the selector dial..on top of bottom portion of vac.....with vac in upright position, recline it as if about to vacuumn floor...look down at selector area ...you should be able to see a rectangular type button exposed ..push this to reset position...you may have to push it a few times...then try vacuumniing.....I finally had suction from soleplate!! Another tipoff to this problem is my selector dial would not stay in place would pop I to carpet by itself, but only halfway....fro a long time my vac would work but not very well...had to go over same area.4-5 times..What a workout! The first time I contacted dyson via tele the rep had me remove some stuff and I was able to look at area below selector...what I saw was two holes, one hole was only over the other hole half way...hence at that time I had only part suction since holes were not aligning properly....I read somewhere as a further tip to get suction to engage, while vac is reclined step on front edge of vac head it said you'll get more suction that way, I haven't tried that, but thought it may help someone
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson hose sucks good but, when i put handle down, it won't **** but brush does turn

I just had the same problem....suction from wand, but no suction from soleplate, the brush bar spins. Did all the troubleshooting steps on dyson.com but they didn't work...dyson.com says need to take to repairman, being a diyer I went to search engi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brushes wont turn,but it has good suction for the hose

If the belt seems to ok, you may need to order a replacement clutch assembly. These are not that expensive and can be ordered through dyson or possibly online. Switching from bare floor to carpet while the motor is running is really stressful on th ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Sebo upright barged hoover- good suction using hose, brush wont turn, sounds fine when running, nasty wineing noise when stopping?? help!! i love my hoover, have checked for bolckages....

The real clue seems to be the brush is not turning, a bad belt is possible or a blockage at that head, if you cannot get the brush moving the rest does not matter. ... Sebo Felix Classic Bagged Upright Vacuum

The vacuum sucks good, but the brush on the bottom wont turn, and the belt seems tight

Even tough the belt is intact it still might need to be replaced. Here is a replacement:Dyson DC14 Belt and Manual ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda

You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx

Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc41 wont suck up on hose and hose pulls back when turned on

... Dyson Bagless Upright Vacuum DC41 Animal

Bissell cleanview - brush not turning. can i fix it...vac is 3 mos old? brush turns freely by hand. suction is good thru hose.

Put a new belt on it ... Vacuums

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?

... Dyson DC25 All Floors Bagless Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob

Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

My sebo automatic X1 has stopped sucking from the bottom. The hose is sucking well but when I put my hand underneath the bottom part there is no ****. I have cleaned the brushes and cleared the way but to no avail. The bag is only half full so I don't think that is the problem.

... Sebo Automatic X1 Bagged Upright Vacuum

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?

If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

I put in a ne Kirby Bag and it still is not sucking up the dirt. The brush is turning but the bag does not seem to be getting any sucking snce it is not expanding

See if this helps:\015\012http://www.goodvac.com/kb_results.asp?ID=13\015\012\015\012Good Luck,\015\012Rocky ... Kirby Ultimate G Bagged Upright Vacuum

My Hoover Mach 5 model number u5194-900 series ZF12.O will vacuum for about 15-10 min then it shuts its self off and will not turn back on., I have cleaned out all the hoses, filters and cleaned off brush. What can I do to fix this so that it will **** into the chamber. The hoses get clogged and it doesn't appear to be sucking into the "bag area"

... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

I have a kirby G7D model ultimate g, the diamond edition. i took the brush part off , and used the attachments, i put the brush back on, and now it wont turn on.

Did you happen to hit the N/D switch by accident on the bottom. The switch has to be in D to run. ... Kirby G6 Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?

This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

Every thing clean & sucking well except wont pickup off floor. brush in good condition &rotating. any answers would help.

This is hard to answer without see it in person. Check and make sure there is no broken pieces on the bottom where you could loose suction. Also make sure you have the machine set correctly for either bare floors or carpet. If it is on set on carpet ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]

Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Brushes wont turn, therefore not sucking up dirt

Check to see if you have a broken belt which is connected to brushes to make them turn. ... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I was putting some bedding in a bag for storage and decided to ''**** it down with my dyson hose to fit it in a smaller space. My dyson quit working and now it will not turn on can you please help...??? I know I didn't **** anything up but I can't live without a vacuum!! I have tried the brush reset button but can't find another reset...

There is no other reset. The Dyson will cut out if it gets too hot, but resets itself when it cools. In doing the job you describe, I doubt that you have operated it long enough to cause overheating, or to do any other damage. I suspect the problem i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0929 seconds