Having problems with your Dyson DC07 Animal Bagless Upright Cyclonic Vacuum ?

No suction Brushes won't turn, belt attatched to motor but not spinning I have no suction in main part of the hoover.

Answers :

Are you saying that the motor runs but there is no brush rotation ?
\015\012If yes then firstly switch machine on then when you pull handle back as if to vacuum the carpet the clutch drive dial must turn to (drive, start, on,) position if it is stuck on (park, off. Stop, p,) position rotate it to drive etc as you pull handle back providing the clutch & both drive belts are ok the brush will spin.
\015\012The clutch drive dial knob is situated looking from the front of machine lower left hand side approx 50mm or 2” in diameter.
\015\012Please do this test & let me know results
\015\012Regards Chris..
Repair Help & Product Troubleshooting for Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction Brushes won't turn, belt attatched to motor but not spinning I have no suction in main part of the hoover.

Are you saying that the motor runs but there is no brush rotation ?\015\012 \015\012If yes then firstly switch machine on then when you pull handle back as if to vacuum the carpet the clutch drive dial must ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a Hoover Steam Vac All Terran floor shampooer, I have taken apart the brushes and other parts to make sure there are no clogs, but it still is not spinning. What else can I do? the Motor is working fine. and the suction is fine too.

There may be some substances such as dust or sand stuck in the spinning parts of the wheel. The substances are restricting the mechanism to work properly and causing blockage in the rotating causing your problem. Cleaning every part of the motor's ro ... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My Hoover steam vac dual v's brushes will not spin and the square that the peg goes into wont spin either. There is suction but it is making a loud noise.

Sometime when the brush is not turning their are less resistance to the motor, so it will turn allot faster than normal. The turbine gear assembly which connected to the brush assembly probably broken, all the g ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

No Suction I have a dc18 dyson and it had lost suction from the main hoover and the hose part. If you remove the dust collection part there is suction from the hole behind that part. I have cleaned all part to this hoover but the problem is still there. Any help would be apprieciated. Thanks

Filter removal step 1Turn power off and unplug the machine.\015\012\015\012To remove the washable filter: Rem ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks

If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

Brush wont spin, belt is perfect

It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs. ... Hoover U8188-900 Bagless Upright Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan

I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?

Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My hoover spin brush steam vac brushes wont spin

Unplug vac turn it over and check for belts that drive the brushesThey are located at the very end of the brush They are probably missingor they snapped and sitting in the housing somewhere. If you ar mechanically inclined not very difficult ... Hoover Vacuums

I have the Eureka Whirlwind upright vacuum. All of a sudden there is no suction- the hose has suction but not main part. I have no idea- but the brush part is not turning??? should I get a new vacuum or is this an easy fix? thanks!!!!!

If the belt isn't turning then it has snapped. Check the top of the hood for two or three crosshead screws; two at the front and one under neath by the left hand side if looking at the upright from the front. Its easy to fix if you take your ti ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

No suction power ,brush wont spin on carpet power nozzle. When it

You need to replace the belt that turns the brush. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Beater brush wont spin for the hoover pet rewind

... Hoover WindTunnel Pet Rewind Upright Vacuum

I have hoover steamvac models f5889-900 and f7222-900. The brush motor is broken in model f7222-900 and I replace with working motor in f5889-900? I am using f5889-900 just as parts

... Vacuums

When my dyson dc14 hoover is on it has a strange burning smell, and a noise like air popping, there seems to be suction from beater and it spins. and definitley suction from extension. Filters are clear and no blockages. Is it the belt I don't think it is. or motor ? Grateful for any advice.

It could be the belt. However, the popping sound does have me puzzled. The popping could be coming from a partially broken belt slapping against plastic.Jim ... Vacuums

Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?

I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums

My dyson DC07 has no suction. motor runs, brush spins, just no suction.

Hi..the reason to this problem may be the bottom pieces \015\012might not have been fully seated.Take it apart and put it \015\012carefully back together.This will solve the issue.\015\012check it out..\015\012thank u..\ ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?

Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover h3030 Brushes do not spin,I have put in a new brush motor drive.

In thi picture, did you replace #20? It is what drives the brushes.\015\012\015\012 ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Hoover Elite Deluxe rewind... Air flow indicator stays activated, after filter has been cleaned. Brushes spin, but very little suction. Dirt is not spinning in cup

... Hoover Vacuums

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!

That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1189 seconds