Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

DC07 brush wont spin on bottom, took all apart and wont work

\015 The only thing that works is the wand, and we took it all apart and put it back together. The bottom brush wont spin and nothing is being sucked up. Any ideas?\015

Answers :

Hi
the belt is broken or stretched, replace it
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DC07 brush wont spin on bottom, took all apart and wont work


Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand


In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

I have a hoover steam vac f5899-100 the brushes doesnt spin...everything else works but tha. we took the brushes apart to clean


There is no belt it is air the gears stick open it up and spin them free ... Hoover F5899-910 SteamVac Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I can't get the brushes to rotate on my hoover steam vac v. i took them apart and cleaned them and they still wont work. any ideas?


Scrubbing brushes are driven by a belt. The belt either broke or slipped off its pulley. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Dyson DC07 is screaming load. I have replaced the lifetime filter and the hepa filters. I also replaced the clutch and brush. I took the canister apart and cleaned it. It works, but is so loud something else must be wrong


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover steamvac brushes don't spin. everything else works great. Took it apart and no visible problems


My husband took it apart today and the impellers were gunked up with black stuff. \015\012\015\012he used these pictures that someone else generously posted. ours was slightly different in internal design, but they are helpful regardless ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin


The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Bissell 3750 bottom brush will not spin belt is fine and lift off works great


Hey Jessica! Please contact us for assistance regarding your vacuum.Here's a quick link to assist you:\015\012http://www.bissell.com/contact-us/?cid=ccsocial ... Bissell 3750 Lift Off Bagless Upright Vacuum

My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?


The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?


There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Took Roomba apart to clean and now the pick up brushes start and stop during cleaning. The vaccum is clean but will not constantly spin. Runs great but pick up brushes start and stop. Is there a number for Roomba? Warranty? This one is less than one year old.


You can go to www.iRobot.com . This is the roomba website. You should be able to find replacement parts, customer support, videos or the Roomba product, and more.\015\012When y ... iRobot Roomba 530 Robotic Vacuum

Brissel Healthy Home Hepa Vacuum: On/Off Switch works sporadically. Took handle apart and the switch worked for a while. I am wondering if I need to replace the switch? Also the Brush Switch is having similar problems.


Might not be the switch there is a connection on the swivel by the base that likes to fail ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have a 8955 riccar vacuum. my roller brush is not working very well on the carpet . I took it apart and now I am not sure on how it goes back together. Could you send me a picture of how the rooler part of the roller brush goes back together. Thank You. Paul


... Riccar 8850 Vacuum

Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.


The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0795 seconds