Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Can't get beater bar back on Dyson Animal - it won't set back into the machine correctly.


Answers :

The bearing blocks must be oriented correctly. Take the belt off and put the brush in place. Once you have it in, mark the surface that is visible with a dot of white out, nail polish or marker, depending on the color of the block. Remove the brush & put it back in, using your marks as reference. The bearing blocks are not square, they are slight rectangles.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't get beater bar back on Dyson Animal - it won't set back into the machine correctly.


The bearing blocks must be oriented correctly. Take the belt off and put the brush in place. Once you have it in, mark the surface that is visible with a dot of white out, nail polish or marker, depending on the color of the block. Remove the brus ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

BEATER BAR QUIT WORKING ON DYSON DC07 VACUUM CLEANER - DIDN'T KNOW IF THERE WAS A RE-SET SWITCH OR HOW TO GET THIS TO WORK AGAIN


Hi its Darran at Dyson. From your description of the problem, either the brush control has been switched off (dial on the side of the cleanerhead) or the belt has snapped which may indicate a problem with the clutch. Please ca ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet


Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?


Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

I have a Yamata GK367B refurbished machine, an older model and the manul is mostly in Chinese and very bad pictures. I need better information about how to thread my machine and to set the tension correctly. I am a professional and need this machine. But it has never worked correctly since I bought it and the company will not take it back. So please help me. Jill G. Arellano


We have no material at all for this brand, sorry. ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I recently put a call into dyson regarding a problem with my vaccuum and a supervisor was supposed to get back to me. no one has. back in august, we were on the phone with a technician regarding a problem with out machine. after trying a list of things, she said to take it to american vaccuum services and it would be covered by dyson. when i did, the man told me it was clogged and i would owe $45. i would not have taken it for that price! please advise as now i am stuck. i want my vaccuum and th


Unless you can Dyson to intervene and have this repair covered under their warranty, You are stuck to pay for the service. Clogs may not be covered under warranty, but I don't know how their warranty states. If it says that if you have a problem, t ... Vacuums

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.


It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar switch on my dyson 24 gets stuck in the off position. I have to push it many many times before the beater bar engages. How can I fix this?


... Dyson DC24 All Floors Vacuum New Upright NEW

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The beater bar on my dyson DC28 is not turning when it is placed on the carpet. If you lift the sweeper up the beater bar will turn but then when you place it back down on the floor it stops.


... Dyson DC28 Animal Bagless Upright Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes


Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums

The beater bar wont rotate when set to floor cleaning on bissell aromatic carpet shampooer


... Bissell Vacuums

Correct position of beater bar on a Dyson DC14?


I had the same problem. I removed the brush from the machine. The brush should move freely when removed. If it doesn't move freely, pull the ends from the brush, both ends come off(one will have a rod fixed to it). I would suggest you clean the ends ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna


... Singer Vacuums

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

When taking the handle/wand back to use it seems to lose the suction power regardless of what setting I use. Upon several times of standing it back up it seems to engage the suction power correctly is there a button or something that does not always engage to get power? can I fix it


When you say taking handle back I assume you mean the action to start rotation of brushes. Had simular problem and found by removing brush from tube and then cleaning "baked on rubbish" in plastic tube (so you can see clearly through tube) Clean with ... Dyson DC28 Animal Bagless Upright Vacuum

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?


Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

I have a necchi sewing machine model 4795 and I am having trouble trying to do zigzag stitch for applique. Can you please help me with the settings on the machine. I have tried to use manual, but I still cannot get it to stitch correctly. Thank you.


... Vacuums

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Help i can get suction from the hose but when i stick it in the back of the carpet head i get no suction and the beater bar will not turn. can you help


... Miele S184 Powerhouse Bagged Upright Vacuum

Dyson dc25 beater bar wont turn - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1416 seconds