Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Yellow Dyson handle stuck in down position will not click upright

\015 Vacuum got caught on bedframe and disengaged the handle from the bottom portion (brush housing), Cannot get it to click into upright position and it will not create enough suction to pick anything up. Don't know if something broke or what is required to bring to upright position. Please advise. Thank you.\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Yellow Dyson handle stuck in down position will not click upright


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC28 handle stuck in upright position - Dyson Ball DC24 Bagless Upright Vacuum


You DO NOT have to take your machine to a "certified technician" to fix this problem. Stand behind your machine, lean over and look at the front: Right in the center of the opening between the machine and the beater bar head, you will see ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 Animal Bagless Upright does not click to stay in an upright position. It works but the handle falls to the floor.


This is a common fault with the Dyson DC07 (and other Dysons) unfortunately the clip that holds the handle upright hs broken. It can be repaired, but will cost a reasonable amount to have done... I would just live with the problem and prop the vacuum ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc24 won't click back to upright not used position .. It's stuck in rolling posistion


... Vacuums

My dyson ball won't click back to upright not used position .. It's stuck in rolling posistion


... Vacuums

Dyson stuck in upright position


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC28 Air Muscle Vacuum that is stuck in upright position


This turns out to be an easy fix.\015\012\015\012First, get some graphite lube. \015\012\015\012Lay the vac on it's 'face'. \015\012\015\0121) On the underside of the vacuum, there is a 1/2" wide 'groove" in the ... Vacuums

The handle on the dyson dc25 is stuck in the down position wheels will not lower


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson DC41 animal complete stuck in upright position - how do I get it down. Have been on hold with Dyson for hours.


The wheels are probably jammed and won't recline. Mine was stuck pretty bad, and after a half hour of trying to figure it out I just picked up the vacuum and slammed the wheels pretty hard, and it came loose. No problem since. Pushing on it hard d ... Dyson Bagless Upright Vacuum DC41 Animal

Dc41 stuck in upright position - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi Patricia, it's Jack at Dyson.I'm sorry to hear you're having difficulty with your DC41 Animal. If it's stuck in the upright position, this may be due to a blockage in the changeover valve. This should be simple to resolve - please follow t ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Motor loud I have a dyson dc17..recently when i turned it on and pulled the handle down to vacuum the motor was very loud..put the handle in the upright position it is quiet.any suggestions?


When you put the handle down it turns on the brush roll. you may need to clean the brush roll or replce it if the bearings are bad.also clutch and 2 belts are started when putting handle down for brush operation. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The handle will not click into the upright position-only stays in "vacuuming position". How do I fix it? Linda from KY


Go to www.dysonmedic.com scroll to bottom of page and click on "DC04 not positioning upright fix" for illustrated solution. The DC07 is similar. If this doesn't work, post a reply here and we'll see what else you might try.\015\012Good luck! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Handle on Dyson ball does not click back into position. This means that when you are hoovering the handle moves back and forth as you move the hoover instead of it being


... Vacuums

Dyson wand stuck wrong way in handle - Dyson DC25 All Floors Bagless Upright Vacuum


... Dyson DC25 All Floors Bagless Upright Vacuum

My Dyson DC25 got stuck and wouldn't return to the upright position, I figured out that one side had jumped the track and gotten stuck in the square hole below the track. I did not want to break the plastic to force it back, so I removed the screw on the right side that was holding the kick stand on and removed the kick stand, also a spring thing came out. Problem is, now I have no idea how to re-install the kickstand. Can't find a technical manual or video anywhere, it can't be very difficul


... Dyson DC25 All Floors Bagless Upright Vacuum

Wont click back into upright position - Dyson DC07i Bagless Upright Vacuum


... Dyson DC07i Bagless Upright Vacuum

I have a Dirt Devil upright ddup1800 and it is stuck in the upright position. There is no switch or level. You stand on the front while moving the handle backwards to get it to move. However, not today. Help?


... Vacuums

Handle relase stuck in upright position and I have the vacuum apart and I dont know what to do what am I looking for it is still stuck


Dirtdevil vacuums are so cheap. it's jammed. just go to a vacuum shop and get it repaired ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Dyson Ball Vac won't return to upright position


... Dyson Ball DC24 Bagless Upright Vacuum

Dyson ball not picking up when using in upright position. I can see the roller is stuck, with carpet twine, how do I open up the case?


Look at the endcaps of the brush nozzle there will be two plastic screws to unlock them, they rotate off. the brushrolls should pull out. what is the model #? ... Vacuums

I have a Dyson DC25 Animal Vacuum. The handle is stuck in the down position. How can I fix this?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC-18 won't click and stay in the upright position. Ideas?


Hi its Darran at Dyson. It is difficult to confirm what may be causing this, however its worth ensuring that when you lock the machine back up into the upright position position, that you push the handle slightly forward when you try to d ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Vacuum handle stuck in down position - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0549 seconds