Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

The brush stopped spinning on my Dyson upright

\015 My vaccuum was fine for a few years then all of a sudden it will just stop working. If I try a few hours or a day later it is fine. Now my brush will not spin. I cleaned all the strings, etc.... from the brush and looked at the belt. The vaccuum does not make weird noises or do anything out of the ordianry.\015

Answers :

Hi there'
\015\012 common possible defective is that motor is not functioning,several factors can be check if you have a knowledge on electrical and motor
\015\012circuit you can easily diagnose your problem on your vacuum.
\015\012 check the switch by your multi tester,if there is a continuinity resistance using multi tester.if no continuity replaced switch
\015\012 check the carbon brush of the motor if worn out, replace two pcs. of carbon mounted inside the motor casing
\015\012 you can check also the continuity of electrical cord and plug.replace if if plug and electrical cord is defective.
finally the motor has winding coil,at both end of coil of motor check the continuity,there are two coils of the motor.if burn out replace motor w/ two pcs. of carbon brush.
\015\012 besure to unplug the vacuum before doing
\015\012this and this should be done by qualified technician on your service center.have a nice day.rate my fix.thank's a lot
\015\012
It sounds as if you need to change the belt. As you run the upright, the belt warms up and stretches. It will then cool down after you shut it off, therefore shrinking back down. This would explain why it works when you first fire it back up.

Jim
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush stopped spinning on my Dyson upright


Hi there'\015\012 common possible defective is that motor is not functioning,several factors can be check if you have a knowledge on electrical and motor\015\012circuit you can easily diagnose your problem on your vacuum.\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brushes have stopped spinning,how do i get them to spin again on my dyson slim? We have tried the brush button


One possible problem could be a worn clutch. I just had the same problem. Before buying a new clutch assembly, I took the out the clutch just to make sure I could do it (the link previously mentioned is great: ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

My sd40025 dirt devil ..it is not a upright. it is the follow along, bagless vacuum. has wonderful pick-up but the brush stopped spinning when i was vacumming my rug..i love this vacumm but it is only the third time i have used it. It is brand new. Why would the brush stop after maybe 20 minutes of total use?..please advise


... Dirt Devil SD40020 Bagged Canister Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson dc 39 brush stops spinning when vacuuming


... Dyson DC39 Animal canister vacuum cleaner

Dyson dc24 roller brush stopped spinning


... Dyson Ball DC24 Bagless Upright Vacuum

Dyson dc30 brush bar not spinning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc 33 brush bar not spinning - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

It stopped sucking @ brush stopped turning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Usually on this vacuum those two problems are not related, but if you got a lot of stuff stuck in the brushroll and in the suction tube at the same time it could happen. Check the belt to make sure it's not broken. If the vacuum is over a year old th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc33 brush bar wont spin - Dyson DC33 Multi floor Upright Vacuum Cleaner Blue- Refurbished


... Dyson DC33 Multi floor Upright Vacuum Cleaner Blue- Refurbished

Dyson dc 25 brush stopped working - Dyson Ball DC24 Bagless Upright Vacuum


Hi there,I'm sorry to hear you're having difficulties with your DC25. This machine has a sensor which shuts off the brushbar if something jams it. Once you've checked the cleaner head for obstructions, and removed any threads or hair from aro ... Dyson Ball DC24 Bagless Upright Vacuum

I have a dyson animal dc24. It is 7 months old and has stopped working. The hand tool is working fine but when I insert it to engage in normal vaccuming the suction stops. I can hear a strange air sound. Also the brush is spinning but it is not picking up. I have taken it apart and checked for a clog but I don't see one. Any advice?


Hi there,I'm sorry to hear your DC24 Animal isn't picking up as well as usual. Although I note you've already checked for blockages, it sounds as though this is likely to be the cause of the issue.To locate and remove any blockages, p ... Vacuums

My Dyson DC 14 brush does not spin - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


It sounds like a worn belt or broken belt. The belt should be fairly snug. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.


Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

My dyson dc07 brush is not spinning - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush doesn't spin. no suction felt at brush - Dyson DC14 All floors Bagless Upright Cyclonic Vacuum


Check that the brush has not become fouled with string, etc. If it still doesn't work try the following.\015\012\015\012Some Dyson's have a switch for the brush on the front of the handle. If yours does, please make sure its on. This m ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Dyson Brush Bar Always Spins


Hello there my dco7 brush bar just spins all the time.but with it upright it stop spin,is this correct.. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc24 motor stops when brush bar switched off


... Dyson Ball DC24 Bagless Upright Vacuum

Brush stopped spinning from fabric being sucked into it, how can I fix it? It's a Dyson animal vacum. The belt is not moving from the lower motor.


Turn upsidedown.\015\012There should be 3 plastic screws in a triangle shape.\015\012Loosen, but do not attempt to remove the screws.\015\012This will release a shield that will expose the brushes.\015\012Carefully remove the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My brushes stopped spinning. What do I do? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Sounds like the brush belts has snapped and needs replacing, you should be able to get a replacement at most electrical stores, just take the make and model number with you. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0788 seconds