Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Just stopped mid hoovering and now won't switch on!

\015 My Dyson DC07 upright will not switch on. It stopped mid-hoovering and I thought we'd had a power cut but no. Checked the fuse in the plug and that's ok. What could it be?\015

Answers :

It is probably a thermal cut-off which is caused by a blockage. The machine will turn itself off before it overheats if it is a thermal cut-off. Once it has cooled down, you will be able to turn it back on again (usually 30 mins - 1 hour).
\015\012
\015\012If the machine doesn't turn on at all anymore, you may need to replace the power switch. Call the Dyson helpline, they will do a blockage troubleshoot and if it's not that, they will tell you where you can find an authorized Dyson repair dealer in your area.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just stopped mid hoovering and now won't switch on!


It is probably a thermal cut-off which is caused by a blockage. The machine will turn itself off before it overheats if it is a thermal cut-off. Once it has cooled down, you will be able to turn it back on again (usually 30 mins - 1 hour).\015\ ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh


Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums

I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.


This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums

Why doe my hoover mach3 stop during operation? I have to wait until the moter cools down.Then i turn on the switch normal way.Then a few minutes latter it stops again.


Your Hoover is stopping because it is overheating. This is a sure sign that there is a blockage somewhere. Find the blockage and clear it, and that should solve the problem. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hi my hoover vacuum, stopped working,does not even turn on,I accidently went over a shoelace but stopped before the shoelace went in, ,,becuase of that the belt came off,and then i put belt back on, and now it wont even turn on


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Sebo upright barged hoover- good suction using hose, brush wont turn, sounds fine when running, nasty wineing noise when stopping?? help!! i love my hoover, have checked for bolckages....


The real clue seems to be the brush is not turning, a bad belt is possible or a blockage at that head, if you cannot get the brush moving the rest does not matter. ... Sebo Felix Classic Bagged Upright Vacuum

The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda


You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums

Henry hoover wont switch on


... Vacuums

The wet pickup and the dry pickup switch on my Hoover Floormate have stopped working. Only the scrub cycle works. Needless to say, it will not pick up wet or dry. Can you tell me what the problem may be and how to repair it?


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do


I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Hoover the on-off switch could be the problem will start and stop by itself. model is u2440-900 series is zh12.0 1200.60hz 12.0.a this product is easy to handle havent had that long of course made in china


A common problem with hoover vacuum cleaners is that a wire breaks inside the insulation just where the power cable enters the machine body causing the erratic on off situation you describe.\015\012\015\012There is a connector box inside ... Hoover Vacuums

I have an Electrolux compact power 1500 hoover which wont work at the moment, when i plug it in and switch it on the green bulb lights up but no sound or suction. any ideas??


... Electrolux Compact Canister Vacuum Powerhead Belt

Hoover windtunnel will not start i used it for a while tell i switched electrical sockets now it wont stArt


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover U5780-900 Windtunnel a month 1/2 old just started stopping when it is running and wont turn back on for a few hours why?


The motor has a thermal protection sensor on it. So your motor may be going bad, it is pulling to many amps for some reason, could be a clog somewhere or a bad bearing in the motor. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Today i was hoovering, and then my dyson just cut out! i left it a few hours then went back to it, it gave a little noise when i switched it on, then again i tried but it failed to come on! ive even changed the fuse in the plug! and now my dyson wont turn on at all, ive cleaned everything there is too clean! help! :D


It looks like you need a professional repair. If you're really lucky this may just be a break in the flex, or the switch has failed - both relatively cheap and simple to sort out. More likely, though, is a problem with the motor (carbon brushes worn ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson has stopped working. There was a burning smell and then a strange noise and now it wont even switch on.


The Motor sounds like it has gone bad. Bagless machines like these always have motor problem. If it is under warranty then it will need to be shipped to Buffalo New York. I would trade in in on a Riccar vacuum. You can get 20 years out of those f ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

Dyson DC07 switched off whilst hoovering, It would not turn on, 1st it stopped rotating brush and than tuned off completly.. I tried ttoi change the fuse but still not turn on. Motor not runnung either.


Hi its Darran at Dyson.Our machines are fitted with a thermal cutout switch. This will activate if the motor on your machine becomes too hot. This is caused by a lack of airflow to the motor, which is caused by a dirty filter or a blockag ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Hoover duros s3590 just stopped running. The motor started up and then just powered down and won't start back up. Is this a faulty on/off switch or a motor problem. I'm weighing the +/- to fix or buy a new vac. TIA


... Maytag Hoover Duros S3590 Vacuum (Canister)

My Hoover steam vac is stuck on the tools setting and wont stop leaking water from the tools hose


... Hoover Vacuums

The henry hoover just stopped and wont work at all. think the motor is bust it is the old normal henry - it has the re-usable bag in it


... Numatic Henry Bagged Canister Vacuum

My 5200 hoover spin scrub all of a sudden stopped sucking in mid clean.i took the front clear cowling off and checked for blockage but couldnt see anything.there is nothing to these thiings,they are disposable it seems lol


Most likely your vent for the suction container is plugged or the suction hose can of or is broken at the connection to the tank nozzle (very common on these. Clean the machine thoroughly, and check that all hoses are tight and connected. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0526 seconds