Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Pulling up on button will not release bottom of cannister.

\015 I can not get the bottom of cannister open to dump contents by pulling up on the release button. This vacuum has been in use for several years and we have never had this problem happen before.\015

Answers :

The gasket is sticking to the dump lid. While holding it over a waste receptacle, operate the release button and pull the waste gate at the same time. Rinse the canister and dry thoroughly. Apply a spray of silicone to the gasket surface, let it sit for a minute, and wipe off the excess with a paper towel. This should fix you up.
\015\012Best regards, --W/D--
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pulling up on button will not release bottom of cannister.

The gasket is sticking to the dump lid. While holding it over a waste receptacle, operate the release button and pull the waste gate at the same time. Rinse the canister and dry thoroughly. Apply a spray of silicone to the gasket surface, let it s ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I press the start button and sometimes the motor won't continue running. As soon as I release the start button, it turns off. Sometimes, if I remove the cannister and replace it, then it will run correctly. Sometimes not.

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I fill my dunhill gas lighter with gas using a Swan lighter refill?Yje lighter is about 2.5 inches long and about 0.5 inches wide with a release button at the bottom

... Vacuums

On the dc07 Animal ,when the release trigger is pulled to allow the rubbish to fall out of the bottom of the shroud the flap does not open being jammed shut

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Liquid dispense i pulled the brushes out of the bottom to clean by using the releases on each side. NOW i can't get the fluids hose on while trying to put the brushes back in.

Try putting the fluid hoses in first then the brush \015\012"you can only put one pant leg on at a time" ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover Z400 bottom half will not release and unfold to an upright position

... Hoover U9125-900 Z Bagless Upright Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C

... Filter Queen Majestic Canister Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Manual I realize it's probably something simple but how do I release the Cyclonic Chamber on top of the Dust Cup lid? I see the red 'open to clean' release button but how do I get down in there to push the release button? Thank you in advance for your help! Best, Christy

Manual > http://www.sharkclean.com/manual/NV22-NV22C-NV22P-NV22T-NV22Q_REV_1008.pdf ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Release button Where is the release button to adjust the vaccum from its upright position, so I could vaccum carpet?

There is no button. You are supposed to place your foot on the area above the rolling brush and hold the base down while pulling the handle back.There is a small metal clip under the vacuum that you should bend out a bit to make it easier to re ... Euro-Pro UV209 Upright Vacuum

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?

I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)

Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne

... Hoover S3614 Vacuum

Release spring popped off when dumping the cannister.

As long as the black piece still has the "nubs" on both sides at the turn in the "L" shape and the base isn't broke then this is going to be easy. There is a groove on the main unit the little wheel fits into that groove, the "nubs" fit into small ho ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bin bottom release snapped off. How do i open the bottom?

Take out the three screws on the to near the handle inside you will find the remains of the old part you can either replace the old part from the top and put it back together to open it normally or you can use the old release stick to push down the c ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover steamvac when I use it it leaks out of bottom. when it off an water in tank leaks out of bottom,when its off an I pull the triggar it flows big time out of bottom. tank doesnt leak when off sitting with water in it

Let me start out with an apology. I did not ask my question very well - and you did not answer it as I needed.\015\012If you wish, we MAY be able to communicate in your native language. We can do most indian languages, Turkish, Ukranian and s ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Error light will not go off. I just bought new batterie, as I thought that was the problem. If I hold down the power button and the play button on the vacuum it will run. When released it stops. The remote will work for the unit if I am holding down the power button on the vacuum.

... Infinuvo QQ1 CleanMate 365 Robotic Vacuum

I have a digital alarm clock from Next - it has the followin gfeatures a mode button - none of the options include time or hour etc an alarm on/off button a button with plus at the top and minus at the bottom. I'm trying to reset it because of the clock change and am baffled.

Hi Karen,Sounds like a neat clock! I can't find anything about this clock. Other projection clocks set the time change automatically. What happens when you try to push the + button. Does it set the time ahead?Also, what ... Vacuums

My Singer Sewing machine (model 6215) is now only sewing in reverse. After pressing the backstitch button, the button seemed to stick in the backstitch position. I was finally able to pull the button out but my machine continues to only stitch backwards. What do I do now?

It's stuck inside. Open it up so you can see inside the bottom, look for the feed dog mechanism and you'll find where length of step is varied, this is where the reversing takes place too. Tapping gently and oiling will free it up.lp ... Vacuums

How do I fix wand release button and spring on dyson dc05

... Vacuums

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.

It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Eureka Altima. Dust bin will not pull off for emptying. slide the lever sideways, and dust bin will not pull out. Has two tabs on the bottom. Appears may have the wrong part on this unit.

... Vacuums

I have a Shark Steam Mop S3501CO model. When I press the release button to exchange mop heads, the mop head does not release. Nils Friis

Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom

Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I pushed the on button and kirby g5 starts but when releasing button motor stops

Hello,\015\012You can replace your own Kirby switch with my guide. Here's the link...\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0346 seconds