Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

When vacuuming the floor it does not leave brush marks or pick up anything unless you reach down and lift on the very front of the machine and then it works for a while and quits again

Answers :

The belt is probably worn or stretched. When this happens the belt won't turn the roller brush when it is against the carpet. Here is a link for the manual and links for the belts you need:

DC07 Manual

Replacement belts for DC07 w/ clutch system

Replacement belts for DC07 w/out clutch system
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When vacuuming the floor it does not leave brush marks or pick up anything unless you reach down and lift on the very front of the machine and then it works for a while and quits again

The belt is probably worn or stretched. When this happens the belt won't turn the roller brush when it is against the carpet. Here is a link for the manual and links for the belts you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e

The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started

There has to be a clog or block somewhere - if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?Bets regardsCk ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Roomba Discovery My Roomba Discovery seems to work fine, mechanically, but it no longer seems to collect any dust. (The collection bin remains empty after the Roomba has circulated around the floor for quite a while). The brush has been replaced and spins normally. Does anyone have an idea why this machine's vacuum function no longer seems to work? I would appreciate any feedback. Jeremy

Did you replace the filter? when you remove the dust bin there is a small filter that needs to be cleaned, or replaced. You can buy a maintenance kit that replaces the brushes and filters as well, its good to replace them all regularly ... Roomba Robotic Floor Bagless Vacuum

We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can't keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick

Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner ... Bissell 8920 ProHeat 2XTM Upright Vacuum

My machine ran over some string,made a funny noise and emitted some smoke,the hand suction pipe at the rear works perfectly, the motor runs fine,but the front of the vacuum will not work.thankyou very much, Thomas.

The string bound up the beater bar (brush), keeps the belt stationary, and the motor spindle is just rubbing against the belt and melting it. remove the belt guard, remove the brush, and the belt. clean off the brush bearings (at the ends of the br ... Panasonic Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?

Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My dyson 25 animal has lost suction from the floor portion of the machine. All the hot hair is coming off the front bottom part, by the ball. Its as if the connection of air has been disconnected. The attachment works fine, though.

You have a serious clog that must be removed. It is somewhere between the floor and the bag or where ever the dirt goes. Clear it and you will be back in business.\015\012\015\012Thanks for using fixya.com ... Vacuums

No water I have a Bissell 1694 and it is not ejecting the water cleaner solution out of the front of the machine. The belts are ok. The two nozzels and hoses are not clogged and do not have any holes. I think the pump still works because water still comes out of the brush tool.

It is easy to take the top off. Mine has just 6 screws. Then you can see all the tubing and parts. For example, you can unclip the nozzles and see if water flows. Try blowing through the nozzle to see if it is plugged.\015\012\015\012Some people s ... Bissell Powersteamer 1694 Upright Vacuum

My scrub brushes quit working on modelf5915-900 in less than one year this is my second machine in 3 years. Now I'm very angry with hoover company. Can this be fixed and how much will it cost me? Steam cleaners

There are a couple of possibilities: the first and most simple fix would be to replace the brush-block, which simply releases from the bottom by pushing the retaining tabs free. If you pull this out and attempt to spin the brushes by spinning the gre ... Hoover Vacuums

My Bissell Lift-Off MultiCyclonic Pet Upright Vacuum with Detachable Canister, Bagless, 89Q9 quit working while I was vacuuming. The power ceased and now it won't turn on. What should I do?

... Bissell 89Q9 Bagless Cyclonic Vacuum

I have a Bissell Little Green Scruber Model #1720-W that has a broken clip which secures the solution/clean water tank to the front of the machine. Where can I purchase the clip to repair this machine

... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work

It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Machine turns on, has little suction, then stops working.

It would be helpful to know what model of vacuum cleaner you're talking about. Basically though, your machine has a blockage somewhere (hence very low suction), and is cutting out after just a few minutes because of overheating.  You need to exp ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

We have an Epic6500. when we plug it in the machine works without the hose. We even purchased a new hose thinking there was a problem with the hose. However as soon as we put the hose on the machine the machine does not work. What do you think the problem may be?

Wow, this is a good one. I wonder if anyone has wrked on this machine before. Do you remember what happened when it stopped working / Obviously there is a foul up in the wiring. I need more info. When the machine is on does it shut off as soon as the ... Electrolux Epic 6500 Vacuum

I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines "check the tank" light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working

We had to prime the sensor. irobot suggested a turkey baster, but we didn't have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest ... iRobot 5800 Scooba Vacuum

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but that's all t

The spray jet has become clogged from the soap.... just clean it out. same thing happened to my attachment. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell lift off stops working after falling over.

May have a broken cord or switch. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Suction quit working. Someone awhile back said

You have to refit the internal hose. This is the small clear hose at the bottom of the machine. Pull it off where it sits next to the wheel first - make sure that the gray piece of rubber is still on the hose - next, twist the hose off where it conne ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery

Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Vacuum Model 116.24614400 Unplugged working machine to move to a new area. Plugged it in and NO POWER TO MACHINE. Checked plug and it is working fine. Is there a reset button? thanks You, Barb [email protected]

... Kenmore Vacuums

My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.

It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea

Hi, Have a Oster small cappucino machine model 3296-33. Everything was working and I just used it know and the machine will make coffee however the steamer/milk frother is not working? Solutions? Thanks, Amanda

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0509 seconds