Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Does the dc 07 have a clutch plate

\015 Does the dc 07 have a clutch plate\015

Answers :

Yes some DC07 models have clutches.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.


Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Not picking up as well as should be...dyson dc07.... From bottom of powerhead in area of outer clutch actuator the round opening for suction is only open halfway, when I move the outer clutch actuator


... Vacuums

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Clutch Issue How to replace the clutch in the Dyson DC07


Greetings from GoVacuum,\015\012\015\012The clutch repair is not a simple task, but if you watch the video below closely, you can certainly get through it. You'll need to purchase a clutch system (it's best to stay with the genuine Dys ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need to remove the clutch on my Dyson DC07 animal and I can't get the clutch cover off. All the videos look like it should come off easy after removing the three screws.


... Vacuums

HOW TO REPLATE FOOT CLUTCH FOR DYSON DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Does the dc 07 have a clutch plate


Yes some DC07 models have clutches. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC07 Dyson clutch not engaging, thus carlperr beater not turning


As far as I am aware, the clutch mechanism cannot be dismantled, and even if it can, I dont know of anywhere to get individual components.\015\012DC07 clutches are avaible on eBay reasonably cheaply, so best fit a new one. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 animal. clutch


Hi.\015\012\015\012Try this site has manuals for Dc07 clutch remove & refit.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Where does the Dyson Port Plate Seal for DC07 ANIMAL Go


It goes here this is dc17 but this is were it goes on dc07 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dc07 clutch belt keeps snaping


... Dyson DC07 Bagless Upright Cyclonic Vacuum

The clutch on our Dyson DC07 All Floor failed.


You will see how to on utube..... ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I just replaced the clutch on dyson dc07 and it's


Hi there, Yes it likely does need replacing. The only other possibility is that the base plate is installed slightly incorrectly and is pressing on the roller making it unable to move. If the machine makes the same sound without the base plate on rep ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 is excessively difficult to push. The plate on the bottom was replaced & helped a little bit for a while.


You should probably consider fitting a new brush roll. The bristles gradually wear away, to the point where they no longer help to pull the machine over the carpet. A new brush with full-length bristles will almost certainly solve the problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 makes loud noise when on carpet setting bar does not spin, could clutch need replacing?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson DC07 upright vacuum makes a loud noise when I turn on carpet mode. I removed he bottom plate and checked the belt and it looks ok


Did you check the roller brush to make sure it was clear of debris? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 vaccum, the clutch has gone out of it and can't figure out how to remove it


Hi,\015\012\015\012Check out this video on Youtube http://www.youtube.com/watch?v=7_CtaFcc5HU\015\012 \015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC07 is screaming load. I have replaced the lifetime filter and the hepa filters. I also replaced the clutch and brush. I took the canister apart and cleaned it. It works, but is so loud something else must be wrong


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush won't turn on dyson dc07


There was a belt that was to be attached to the motor shaft under the belt cover, be sure that it didn't pop off. the recommended fix is to replace the clutch, not the belts in the clutch. if you only replaced the belts it could still be a bad clutch ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC07 grinding noise


I had the same problem with mine, I took it to a repair shop. The problem is where the belt passes through from the brush and goes inside the machine. Move the belt over a bit and you will see that a plastic guide has been bent over and is pressing o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 is making weird noise


Hi there, it's Jack at Dyson.I'm sorry to hear your DC07 is making a popping noise in use. Unusual noises can be caused by a number of different issues, and in order to determine exactly what's causing this we would need to hear it. I'd e ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0208 seconds