Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

My dyson DC07 upright vacuum makes a loud noise when I turn on carpet mode. I removed he bottom plate and checked the belt and it looks ok


Answers :

Did you check the roller brush to make sure it was clear of debris?
My dyson dc7 makes noise 1 secad then goes dead no power at all
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson DC07 upright vacuum makes a loud noise when I turn on carpet mode. I removed he bottom plate and checked the belt and it looks ok


Did you check the roller brush to make sure it was clear of debris? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.


If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

MY HOOVER UPRIGHT U4581-910 HAS GOOD SUCTION THROUGH THE ATTACHMENTS BUT LACKS THROUGH THE BOTTOM. THE BAG FILLS WITH AIR, THE BELTS AND BRUSH TURN FINE. WHAT SHOUL I LOOK FOR?


... Hoover Vacuums

I have the Electrolux Intensity upright vacuum. The roller bar underneath that is used for carpet no longer turns. I have checked the belt that is attached to it. I'm afraid that it may be the motor. Where can I take it for service or shat do I do now? Kay


... Electrolux Vacuums

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

My Eureka model 2961 does not **** up larger particles. You can see it picks up dust and dirt. Am trying to remove bottom guard plate to check belt but can't take it off.


Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Eureka 2961AVZ Bagless Upright Vacuum

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?


The brush is worn out most likely ... Vacuums

Kenmore canister model numer 26212690 12.0 amps with powermate. How do you remove the bottom part to check the belt. The blade won't turn and the switich is on rug not wood floor. There are two arrows that say to seperate use screwdriver at arrow. Have seperated at the arrows but the back will not come apart.


Hi There,\015\012\015\012There are actually two screws that need to be removed before you can separate the bottom from the top housing. The screws are actually located either underneath of the headlight cover, or on the bottom of the ma ... Kenmore Vacuums

Belt Stretched on my Hoover Windtunnel Farrington upright model U6431-900


Hi, In order to to replace the V belt the one that turns the brush, One must take off the bigger belt " drive belt" that goes over that hugh wheel towards the back. When a belt gets stretched they will not turn the brush very well. If you have bought ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

SHARK CORDLESS SWEEPER 3 SPEED CONTROL FLOOR, CARPET, TURBO BATTERY EURO-PRO 8.4V - 1.3 Ah SB617U 3305 BELT Turned on and almost immediately turned off At least four years old - not used all the time - not used in six months Checked belt - seems O.K. Do I need a new battery, if so, where do I get one? Or should I just get a new sweeper? Cost?


... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1073 seconds