Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?
Lack of suction
\015 Little suction from vacuum\015
I love the Dyson (DC07), but after 7 or 8 years it lost suction and needed some attention beyond filter cleaning. After much online research I found the few bits of advice that for me were the holy grail. After all of the standard stuff, clear clogs, clean filters etc..... In this order: 1) Remove & empty the canister, ***important****-leave the canister bottom lid open. 2) remove the three star screws at the top of the canister. It'll take a bit of pressure to pull the top up, there's a rubber seal. When you pull it up there will be a rod running down into the canister, leave it be, just pull up the top high enough to clear out any debris. 3) Put the top back on aligning the screws, when you lower it make sure the bottom of the rod engages with the hole at the bottom center of the canister, this is why you left the bottom lid open. Put the three star screws back in. 4) Turn the canister upside down, lid open, and keeping in mind this is thin plastic, gently tug upwards on the four fins that surround the bottom rubber seal. This part is held in by friction, so work your way around the four fins gently pulling until you work the ring they're connected to free. This will give you access to the inside of the canister. 5) remove the round perforated section by tugging upwards on it, set it aside with the fin part. 6) Take the canister to a laundry tub or large sink and holding it bottom up fill it with hot/warm water. Grasping the center section shake it vigorously and turn it upside down while shaking and a bunch of sh*t will come out. Repeat several times. 7) Dry thoroughly, you might use a hairdryer held to the center tube, but only if you can switch off the heat and use air only. Make sure its 200% dry, water will kill your machine 8) clean and replace the round perforated section 9) replace the fin section, I'd suggest pulling the round rubber part off of the fin part and setting it in place on the canister first, then follow with the plastic fin part. If you don't do it this way the rubber won't seat properly and the bottom lid won't close. 10) Close the lid, replace the canister, and staaaaaart suckin like it's brand new.
You should check the round filter casing on theleft and the right side of machine to make sure they are snaped in right also the clear hose on the bottom sumtimes comes unhooked.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?
Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue
My magic blue vacuum has no suction. The lid seems loose and the lack of suction seems to be related to the loose lid. I cannot find a way to tighten the lid.
Have u tightened the dirt cup lid. ... Vacuums
Lack of suction with panasonic vacuum mc-e3001
... Panasonic Vacuums
Noisey DC07 Bagless Upright Cyclonic Vacuum; lack of suction...
The washable filters very seldom wear out, they are sponge, but the prefilter on the housing CERTAINLY wears out. You can fix it here:\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Lack of suction
Do not think its motor .......Yoy need to see thats its not Cloged if so clean....... ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Lack of suction
I love the Dyson (DC07), but after 7 or 8 years it lost suction and needed some attention beyond filter cleaning. After much online research I found the few bits of advice that for me were the holy grail. After all of the standard stuff, clear ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Lack of suction
I use a broom handle..works very well ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Lack of Suction and roller not working
Replace your belt. Its probably stretched or broken, also check the bag for fullness and the hose for clogs. let me know if you are still having trouble. ... Fuller Brush FBHD1 Bagged Upright Vacuum
Lack of suction in hose
That popping sound is the bleed valve activating - it indicates that there is a blockage in the machine somewhere, probably in the wand if you're saying that there is no suction in the wand.\015\012\015\012- Take the wand off the back of ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Lack of suction to tunnel, bad seal?
YOU NEED NEW FILLTERS ... Hoover Vacuums
Lack of suction at power unit
If you have remove the piping from the inlet of your vacuum and by clogging the inlet with your hand to feel if it is sucking air but still little/no suction is felt then there must be a crack from the inside of your vacuum unit where most of the a ... Electrolux Centralux Vacuum
Lack of suction even with filter removed.
I used to be a service manager for Electrolux. It sounds like possibly a clogged fan or hose. Take the hose off and check the amount of vacuum at the opening of the cleaner. If it has more suction without the hose, hold the hose in place backwards ... Electrolux UltraLux 2000 Bagged Canister Vacuum
I have the Dyson animal upright vacuum. It's 2 years old and now it just isn't working as well as it once did. Suction seems to be lacking - it's not picking up pet hair or much else from the carpet. I have to go over the spot for a few minutes and still, the hair isn't picked up.
You might want to check and see if your cyclones are plugged with hair. this can happen and there is a great site to disassemble and clean the cyclone here: http://www.exonotes.com/content/node/4 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson dc03 lack of suction
... Dyson DC03 Bagless Upright Cyclonic Vacuum
Lack of suction - Hoover Vacuums
1) clog house , need replace or repair 2) check the belt is broken or worn and replace.God bless you ... Hoover Vacuums
Lack of suction with hoover freespace cyclonic cleaner
MY HOOVER UPRIGHT U4581-910 HAS GOOD SUCTION THROUGH THE ATTACHMENTS BUT LACKS THROUGH THE BOTTOM. THE BAG FILLS WITH AIR, THE BELTS AND BRUSH TURN FINE. WHAT SHOUL I LOOK FOR?
... Hoover Vacuums
Lack of suction on the main part of the vacuum
There are two easy things to consider if you have a lack of suction on the vacuum:\015\012\015\0121. Replace the bag and check the hose leading to the bag to see that it's not blocked.\015\012\015\0122. Replace the belt. ... Kenmore Vacuums
Hi there my dyson suffers from a lack of suction with of without the hose attached. we had our local repair man look at it and he replaced a hose in the head of the machine.i have replaced all the filters and ideas?
What about doing this:\015\012\015\012http://www.fixya.com/support/t2936439-dyson_suffers_from_lack_suction ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
Lacking suction from largest filter I don't know how to remove it
Hi there VacuumGuru for nelsonvacuums and VacuumSpot here. I have actually made a video on how to locate and change your filters for the dyson dc07. See link below. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
There seems to be a lack of suction on the main unit(brushes). Its fine when using the pipe
There is a blockage in the neck where the power head connects to the machine. Remove the base plate. Look behind the beater bar and you will see where the dirt enters the machine. There is likely something blocking the entry into the mach ... Dyson Vacuums
We were having issues with its lack of suction - we took it to an authorized Dyson repair shop and now sparks are shooting out and its smoking! What the heck is wrong now?
Definately return it to where the work was done. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson lack of suction - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Lack of suction in dyson in dc40 - Dyson Ball DC24 Bagless Upright Vacuum
... Dyson Ball DC24 Bagless Upright Vacuum