Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Brush won't turn when vacuum is on? Feels like

\015 Brush won't turn when vacuum is on? Feels like the belt is off the drive. Not sure how to open it up to check\015

Answers :

Three clips under vacuum turn with coin
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.


The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Kenmore vacuum- no suction, brush wont turn


Sounds to me like you have a plugged vacuum. Check all the way through. ... Kenmore 22812 Bagged Canister Vacuum

Kenmore vacuum - no suction, brush wont turn


Sounds like the vacuum is clogged and putting too much stain on the agitator, so I would clean out the entire passage way for the vacuum and replace the agitator belt, you must clean out all the hoses it is clogged somewhere ... Kenmore Vacuums

Brush won't turn when vacuum is on? Feels like


Three clips under vacuum turn with coin ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum


... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums

Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..


The belt may have come of or broke..\015\012Turn the vac over so the bottom is facing up..\015\012Remove the scews in the plate cover that surrunds the brush..\015\012Remove the plate cover..\015\012You will see if the belt is ... Vacuums

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

So i was vacuuming and pulled up a throw rub for about 10 seconds or less. i turned off the vacuum and and now the brushes wont spin. what do you think i should do? Thanks Tommy


You burned a flat spot in your belt - replace it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brushes wont turn and wont spray water - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

Brush wont turn..Pressed reset still no turn - Vacuums


If the motor runs and the brush doesn't turn, the first and best suspect is the belt. ... Vacuums

Vacuum brush roller wont turn - Dirt Devil Featherlite Bagless Vacuum M085845Vacuum


You dont say if you checked if the belt is still whole so my guess is the belt broke(it could've fallen off and not be there at all but you definately need a belt) check that and let us know ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Brush bar wont turn, Bissell smells like burning rubber


The belt just goes from the motor shaft to the brush roll. Do the ends of the brush trun freely, or is one of them froze up, if so replace the brush roll. If it is ok, try to turn the brush roll by hand, maybe the belt got pinched and won't move. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

My vacuum wont turn on.


It sounds like you may have a faulty on/off switch. I suggest if you are not familiar with electricity please have someone that you know "is" to do the following. "UNPLUG" your vacuum and disconnect thee white wire coming out of the on/off switch. Wi ... Bissell 3576 CleanView II Bagless Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

I turn the vacuum on and just make the noise like it's working and the brush is not moving.


I tried everything and this is what solved the problem of the brush not turning and no suction on the brush area. I took off the lid where the roller brush is and cleaned the sided of the roller brush, it was frozen tightly from HAIR. Used a small ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Agitator brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover f7452900 brushes wont turn? - Hoover F7452-900 SteamVac Upright Vacuum


Make sure that you have it on the carpet setting and not the hardwood/tile setting. also if you used the hose, make sure that the little door is closed. if all checked... remove the recovery tank, there should be a rubber grament on the stand pipe un ... Hoover F7452-900 SteamVac Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1336 seconds