Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

THE BELT THAT DRIVES THE BRUSH FOR THE CARPET BROKE'


Answers :

OK - so you need to instal a new one! But before that, two questions: first - why did the old belt break? second - is your DC07 a model with or without a clutch?\015\012
\015\012Belts rarely break from simple old age; the usual problem with this vac is that the bearings in the brush roll get sticky, so it doesn't revolve freely. If this is the problem, it can sometimes be alleviated with a spray lubricant, but the only long term solution is to instal a new brush roll.\015\012
\015\012As for the clutch - if it's got one, there's a knob towards the front right of the floor unit. If it has one, the drive belt is integral with the clutch, and the whole unit has to be changed. If it has no clutch, then installing a new belt is simple. For excellent illustrated guidance, go to www.dysonmedic.com
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

THE BELT THAT DRIVES THE BRUSH FOR THE CARPET BROKE'


OK - so you need to instal a new one! But before that, two questions: first - why did the old belt break? second - is your DC07 a model with or without a clutch?\015\012\015\012Belts rarely break from simple old age; the usual problem with this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a bissell 9300 carpet shampooer..the belt broke o n the left side. tookoff the plasitc brush shield to access the area to put on the belt but not sure how to connect it to both brushes..only one comes undone...do i have to unscreww the whole thing?


Follow the link below on how to change the belt.\015\012http://www.bissell.com/VideoRating.aspx?id=1557 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?


I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Ny Panasonic MC-E4013 has lots of ****, but the brushes don't pick up from the carpet. The drive belts are not broken and the brush roller goes round OK.


Usually, shen you have this problem, there is an obstruction of dirt etc. somewhere in the suction path.You need to take the vacuum apart and clean thoroughly first.Then get back to me. ... Vacuums

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?


Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa


Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

Replacing the brush drive belt on model #1697 carpet cleaner


To replace the Brush Belt:You will need a Phillips head screwdriver.1. Turn the machine OFF and unplug from the wall outlet.2. Step on the release pedal to lay the handle down on the floor.3. Remove the ... Bissell Vacuums

Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.


Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

When selecting the carpet cleaning mode, it appears the belt is slipping (due to the noise) over the drive pulley. How do you access the drive mechanism to replace belt or inspect drive pulley and belt condition?


On those units you must replace the clutch assy. you cant just replace the belt. there is also a special tool used to get the new belts on the brushbar. If you would like me to walk you through this repair let me know. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.


These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Bissell 9200 pro heat carpet cleaner , brushes won't turn, both side belts are good. bad brush motor? or brush moter belt?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes


(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0649 seconds