Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dyson has stopped sucking and it does not swirl in the transparent part when swithed on


Answers :

Hi there, to put your mind at rest, the dirt in the bin doesn't always spin round.

If the bin is filling and the machine appears to be picking up as normal then you have nothing to worry about.

However if you have noticed that the performance has dropped we would recommend checking your vacuum cleaner for blockages and washing the pre filter. Full details on this can be found in your user guide or in the Support section on our website at www.dyson.com.

Kind regards
Darran
Dyson Customer Service
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson has stopped sucking and it does not swirl in the transparent part when swithed on


Hi there, to put your mind at rest, the dirt in the bin doesn't always spin round. If the bin is filling and the machine appears to be picking up as normal then you have nothing to worry about. However if you have noticed tha ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc24 - just tried to use after being in storage, making loud noise and seems to be blowing out rather than in. Maybe a part missing? The hole at the top of the bin attachment is sucking air in.....should something be there to stop this?


The wand attachment at the top is supposed to only suck in when it\\'s in the upright position, otherwise the suction should be used when the vacuum in rolled on the carpet/wood/surface.If it\\'s still under warranty, contact Dyson directly. ... Vacuums

Dyson dc17 animal stopped sucking. brush still


Make sure the flexible hose that connects the beater brush housing up to the connection up by the dust bin is still connected. It could also have a hole in it so check for that as well. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson 07 doesnt **** up when im doing the carpet but the hose works fine? when im vacuming it sucks up very little and the hose part seems to be sucking up air when im doing the carpet? would this mean something is plug??? thanks randy


There is a block in the hose take lower hose of and clean ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?


The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 vacuumn system is stopped up, the clog is in the top part of the vacuum before it drops the dirt into the cylinder. Does the top part of the canister come off so that you can get into the tubes that are clogged.


... Dyson Vacuums

It stopped sucking @ brush stopped turning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Usually on this vacuum those two problems are not related, but if you got a lot of stuff stuck in the brushroll and in the suction tube at the same time it could happen. Check the belt to make sure it's not broken. If the vacuum is over a year old th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson Animal I sucked up a part of sock didn't get sucked up turned it off and pulled out sock but beater brush won't come back on.


Happened to me too. there is a reset somewhere, i got mine working again. try the Dyson website, sorry ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I was in the midst of vacuuming with my Dyson Animal when it stopped working. It smelled as though part of the motor burned up (there was hair and string wrapped around the brush so I stopped to remove it). Any ideas on an easy, quick, and inexpensive fix? Thank you!


Hi there,For guidance on clearing any remaining threads or hair from around the brushbar and resetting the machine, please follow the steps shown in the video below. Please note, the brushbar will never rotate when your machine is upright, so ... Vacuums

My dyson dc07 animal bagless upright cyclonic is giving me problems with the bottom part where it sucks up the dirt the part that covers the brushes is not going on like it suppose to what am i doing wrong


CKECK Clutch Assy and belt\015\012bottom part where it sucks \015\0121: try us WD40... \015\0122: Replaced power switch Part No : 910971-01 ... Vacuums

My sebo automatic X1 has stopped sucking from the bottom. The hose is sucking well but when I put my hand underneath the bottom part there is no ****. I have cleaned the brushes and cleared the way but to no avail. The bag is only half full so I don't think that is the problem.


... Sebo Automatic X1 Bagged Upright Vacuum

My Bissell 3760-1 has stopped sucking in the roller portion. The grab n go part are working fine. Checked the belt and it looks fine. Did I burn up the motor or a microchip?


Hey Lisa! Sorry you're having difficulty with your Lift-Off vacuum. Here's a link to troubleshooting steps to assist you with the suction.\015\012http: ... Vacuums

We replaced the short hose that connects the sucking part to the hole where the dirt goes underneath my Dyson DC07 but now the side of the hose that needs to attach to the machine falls off.


I know the hose you are talking about it is called the DC07 internal hose. Over time the ends can stretch and perish which will mean y ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Vacu-Queen V3000. It stopped in the middle of a job. The plastic housing that sits on the rubber ring at the top of the cannister was sucked part way into the cannister and broke the seal. I cn replace everything but after cleaning the filter it continues to happen. Any ideas how to correct this problem?


... Filter Queen Majestic Canister Vacuum

Using a Hoover Steamvac to clean my carpets. It works fine in some areas, but others it makes a clicking noise and stops sucking water. Once I turn the vacuum off and wait a few seconds, it clicks once more and is okay to use again. Certain parts of my carpet this happens so frequently I can't vacuum.


1)clog in the hose or air/tank full you must , need replace or emptied,test the belt for broken or worn.2) noises can be area motor , test for fan blade defective or broken3) You must go http://hoover.com/support/video-instruction-guides/ for ... Vacuums

Stopped sucking! - Dyson DC14 Low Reach Bagless Upright Cyclonic Vacuum


Have you emptied the dirt and cleaned the filter? Hope this helps. Good luck! ... Dyson DC14 Low Reach Bagless Upright Cyclonic Vacuum

I accidentally sucked up part of a blanket with my DC-17 Animal Dyson and now the roller brush makes a griding noise. Did I ruin the clutch or the roller bar. When I lift up on it slightly it doesn't make the noise only when resistence is applied.


My Dyson started making a loud noise when in "carpet" mode. After reading a ton of forums I thought it was the clutch assembly. Got a new one on eBay for a great price. Somewhat hard to replace, but thanks to this YouTube video, I was able to get it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?


If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Hoover Steam vac has also stopped sucking... I have pulled it apart to clean it. Is there a way to take the bristles off to clean them as well as are there any other parts that could be the problem?


Based on your description, poor suction is related to only a few things\015\012\015\012Check filter inside lower tank\015\012Check the lower tank lid to be on properly\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Dyson just stopped sucking up dirt. I have checked all the obvious things like clogs and filters. I noticed when I turn it on, there is a valve on the top of the cannister that opens and you can feel suction from the vent hole. Is this valve malfunctioning, or is it working correctly because something else is malfunctioning?


Your cyclones could be clogged. You can clean them yourself pretty easily. See this video. http://www.youtube.com/watch?v=2OO3ugkyzxk ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush stopped spinning from fabric being sucked into it, how can I fix it? It's a Dyson animal vacum. The belt is not moving from the lower motor.


Turn upsidedown.\015\012There should be 3 plastic screws in a triangle shape.\015\012Loosen, but do not attempt to remove the screws.\015\012This will release a shield that will expose the brushes.\015\012Carefully remove the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

A large screw got sucked up the vacuum. Since then the motor,which I replaced probably only 12 months ago, sounds very "winey" and when you stand the dyson upright the front brush still keeps going round instead of stopping. Any ideas? David


Sounds like the clutch mechanism has somehow been damaged.\015\012\015\012Have a look at the following site which is a great source of info on faults, dismantling, repairing and re-assembling:\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When the vacuum is on and in the "stand up" position in oder to use the hand held part of it, the top makes a strange sucking sound that it never did in the beginning, But as soon as you use it as a floor vacuum it stops.


IT SOUNDS LIKE THERE IS AN OBSTRUCTION IN THE HOSE AND CAUSING THIS NOISE ... Dyson DC14 Bagless Upright Cyclonic Vacuum

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?


If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0653 seconds