Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Answers :

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here's how to get inside In this order: 1) Remove the canister 2) remove the three star screws at the top of the canister. It'll take a bit of pressure to pull the top up, there's a rubber seal. When you pull it up there will be a rod running down into the canister, leave it be, just pull up the top high enough to clear out any debris. 3) Use a straightened coat hanger and with a flashlight to guide you, reach down with it and push it into that hole down at the bottom center of the canister. That will pop the lid open. Clean the canister & lid rims, maybe add some silicone. At this point you might as well clean the canister too. OPTIONAL-> ***leave the bottom lid open*** and follow the rest of these steps 4) Put the top back on aligning the screws, when you lower it make sure the bottom of the rod engages with the hole at the bottom center of the canister, this is why you left the bottom lid open. Put the three star screws back in. 4) Turn the canister upside down, lid open, and keeping in mind this is thin plastic, gently tug upwards on the four fins that surround the bottom rubber seal. This part is held in by friction, so work your way around the four fins gently pulling until you work the ring they're connected to free. This will give you access to the inside of the canister. 5) remove the round perforated section by tugging upwards on it, set it aside with the fin part. 6) Take the canister to a laundry tub or large sink and holding it bottom up fill it with hot/warm water. Grasping the center section shake it vigorously and turn it upside down while shaking and a bunch of sh*t will come out. Repeat several times. 7) Dry thoroughly, you might use a hairdryer held to the center tube, but only if you can switch off the heat and use air only. Make sure its 200% dry, water will kill your machine 8) clean and replace the round perforated section 9) replace the fin section, I'd suggest pulling the round rubber part off of the fin part and setting it in place on the canister first, then follow with the plastic fin part. If you don't do it this way the rubber won't seat properly and the bottom lid won't close. 10) Close the lid, replace the canister, and staaaaaart suckin like it's brand new.
The clip that pushes the bag door open inside the bottom of the cyclone might be broken. its hard to get these apart without breaking the cheap plastic that dyson uses so be gentle but you will have to pry the lid open if the rod wont let it drop. If that clip is broken i think you will have to replace the whole cyclone assy because dyson doesnt sell the parts separate. let me know if you have any more questions.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 Clear Bin Flap will not release


Important thing is that in order to get the rod in the hole, you have to squeeze the trigger while you are trying to do it. Squeezing trigger makes rod longer. All fixed! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 cyclone release catch will not click (lock) back into position after removing the clear bin assembly to empty the bin.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bin bottom release snapped off. How do i open the bottom?


Take out the three screws on the to near the handle inside you will find the remains of the old part you can either replace the old part from the top and put it back together to open it normally or you can use the old release stick to push down the c ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Want to clean shroud of DC07, have done it before, but this time (and following users manual directions) the bin release catch doesn't seem to be enough to get the clear bin off. It's so stuck together! Help?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc19 t2 clear bin will not release. Catch seems stuck.


... Dyson Vacuums

My dyson animal's clear bin latch is stuck and won't release. I can't take off the bin via the outer shroud release either.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.


... LG Vacuums

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/


3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

The base of the clear bin won't open.


Just had the same problem. Finally realised what to do. Pull the long rod away from the top against its spring (by the rubber gaiter) and whilst holding it, undo the screw holding the long rod to the top trigger mechanism. Now you can wiggle the rod ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Dc35 cyclone release catch


... Dyson DC35 Handheld Vacuum

On the dc07 Animal ,when the release trigger is pulled to allow the rubbish to fall out of the bottom of the shroud the flap does not open being jammed shut


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The water spays out of the bottom all the time and even when you have the trigger released. This happened after the first use.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Jammed release bin latch on dyson ball - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson Dc07 trigger will not release - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum cleaner: AEG electrolux Cyclone XL bagless; the plastic clip (release button) broke off the lid of the dust container. Do i need to replace the entire dust container or can i just buy a new clip?


... Vacuums

My Dyson DC 07 Dust Bin release trigger is broken. Is there a repalacement part?


You have to call Dyson in California and order it...Dyson is notorious for this , and that's how they make money ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson dc07 bagless vacuum cleaner. How do I split the top and bottom halves of the dust collection bin? There is a lever and catch on the side, I have tried pulling and turning, but with no success.


Hi at the top of the Cyclone there is a lever underneath the Handle. The Handle I am referring to says Dyson on it. Firstly you must release the Cyclone from the spine. After doing this you will be left with the Cyclone and the Cyclone Bin all in a ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc29 clear bin stuck - Dyson DC29 Allergy Bagless Canister Cyclonic Vacuum


... Dyson DC29 Allergy Bagless Canister Cyclonic Vacuum

Dyson DC14 Cyclone bin release latch - Vacuums


... Vacuums

My Eureka Atlantis Express is brand new - never used. I took it out of the box, read the manual, filled the soap and clean water tanks, put them in. I lifted the machine off the counter to take into the living room but all the water came running out of the bottom all over the kitchen floor. I can see where the little white plastic piece sticks up into the water release valve and lets the water out. How do you stop this? Can it be fixed?


... Eureka 2553A Atlantis Handheld Wet/Dry Vacuum

DC25 telescoping handle does not seat tightly. When pulling the vac back it unseats about 2 inches. This prevents the hose from engaging securely in the base and suction is affected. Do I need to replace the clear wand release catch? I've only had the vac about a year and am surprised it would wear out so quickly.


... Dyson DC25 Vacuum

DC17 wand release catch won't release. wand stuck


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover Z400 bottom half will not release and unfold to an upright position


... Hoover U9125-900 Z Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0481 seconds