Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

The brush does not rotate at times. The belt is ok. It will not rotate in the stored position, but starts when I drop it to the other position, but not always!

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush does not rotate at times. The belt is ok. It will not rotate in the stored position, but starts when I drop it to the other position, but not always!

... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?

If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dear Sirs, I purchased two Braun 5875 Contour Electric Shavers in May 2009. I didn't start using one of these new shavers until August 2010. In January of this year I found that the contour part of my razor started to flex on one side and the spring clip that retained the foil became loose. I didn't get very good shaves from this Braun razor and put it down to the pattern change of the foil itself. I have always used Braun shavers because I was of the opinion that German made articles were alway

... Vacuums

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

As you turn the Sebo on, the 2 red lights flash once and there is no motor. If you rotate the brush roller the motor starts. We've taken off the brush roller and put it back on and now it doesn't even start when you rotate the roller.

... Sebo Automatic X1 Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Customer service I have had problems twice with returning things at the store. The customer service representives are always so rude. I have shopped at the yorba linda,CA store for the last time. I will not shop at any Best Buy for that matter. You know there are so many stores out there with much better service. I just want to say Good Luck to all Best Buy employees.

Thanks..this is not a Best Buy service desk. But your comments will most likely be reviewed by someone, methinks. ... Vacuums

While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.

The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.

May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My pet hair eraser rotating brush does not rotate. I read the manual and cleaned the brush and placed it back correctly, but it is not working when I am using it. If I lift the vacuum from the flour, it starts rotating so I think it is the matter of the amount of contact to the flour. what should I do?

... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.

Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums

My garage door opener will start to close then stop and go back to the open position. If I put pressure on the door as it is closing sometimes it will close all the way and sometimes it will return to the open position. Can you help me. Thanks

Sounds like the pressure sensor is being tripped - this is a safety feature on most makes in the last 10 years.Find the make/model of your device and it probably has some knobs on the main unit to adjust. For example, on the ... Vacuums

I can't get my animal Dyson to drop down for the brushes to pick up...it is stuck in the upright position. It is so frustrating that I can't get it to drop to vacuum the floor.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not rotating in carpet position tried overload protection reset rotates freely by hand model mc-ul594 bagless upright

... Panasonic Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?

I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

Intermetint starting does not always start when the button is depressed

... Hoover S1361 Bagged Canister Vacuum

What is the secret of installing the belt? When I start in the off position & turn it to the belt on position, the belt is not picked up. It appears that the hook is backwards.

Kirby has produced a good video that shows you step by step how to change your belt. They show the Sentria model but this procedure is the same for every Kirby model. You will notice in the video that they mention the numbers on the side of the brush ... Kirby Generation 3 Bagged Upright Vacuum

How do you get the beater brush to start rotating, the dyson was just cleaned and the beater brush won't rotate

Sounds like the rubber drive band has not been replaced properly to drive the brush and/or the brush was not properly cleaned.\015\012You can find the manual here:\015\012\015\012http://dl.owneriq.net/4/4d79dca8-65d8-4c46-a58a-a2fef1f89635.pdf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My Dyson Animal will not turn on when in upright position or when using the wand. It will, however, start when in the rug vacuuming position (leaned back).

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e

The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The brushes stop rotating on rugs after a few seconds then button has to be pressed to start rotating again but keeps cutting out

Not sure this is your foolproof solution to the problem, but you might give it a try to see if it solves your problem.\015\012\015\012When the beater brush starts to bind up due to debris it retards the action of the cleaner, sometimes to the p ... Dyson Vacuums

I have an Electrolux El8502 Upright Vacuum and the brush roller does not rotate. I took off the roller and the pulley and started the vacuum. I notice that the cam is not rotating. Any suggestions much appreciated.

Hi, you can use thelink below to do a troublshooting tips for your upright vacuum..http://home.howstuffworks.com/how-t ... Electrolux EL8502 Versatility Bagless Upright Vacuum

Loud noise when I start the vacuum in carpet position

It's most likely the Belt Slip Protection Dyson uses to prevent the user from having to replace belts. I recently bought a Dyson and love it other than it literally sits there and makes horrible noises 80% of the time. I completely disassembled ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0562 seconds