Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

I have lost suction.....what do I do? -with the vacuum and the hose!


Answers :

If you've tried everything else, try this:
\015\012
\015\012http://www.ehow.com/how_5870417_modify-dyson-prefilter-suction.html
I love the Dyson (DC07), but after 7 or 8 years it lost suction and needed some attention beyond filter cleaning. After much online research I found the few bits of advice that for me were the holy grail. After all of the standard stuff, clear clogs, clean filters etc..... In this order: 1) Remove & empty the canister, ***important****-leave the canister bottom lid open. 2) remove the three star screws at the top of the canister. It'll take a bit of pressure to pull the top up, there's a rubber seal. When you pull it up there will be a rod running down into the canister, leave it be, just pull up the top high enough to clear out any debris. 3) Put the top back on aligning the screws, when you lower it make sure the bottom of the rod engages with the hole at the bottom center of the canister, this is why you left the bottom lid open. Put the three star screws back in. 4) Turn the canister upside down, lid open, and keeping in mind this is thin plastic, gently tug upwards on the four fins that surround the bottom rubber seal. This part is held in by friction, so work your way around the four fins gently pulling until you work the ring they're connected to free. This will give you access to the inside of the canister. 5) remove the round perforated section by tugging upwards on it, set it aside with the fin part. 6) Take the canister to a laundry tub or large sink and holding it bottom up fill it with hot/warm water. Grasping the center section shake it vigorously and turn it upside down while shaking and a bunch of sh*t will come out. Repeat several times. 7) Dry thoroughly, you might use a hairdryer held to the center tube, but only if you can switch off the heat and use air only. Make sure its 200% dry, water will kill your machine 8) clean and replace the round perforated section 9) replace the fin section, I'd suggest pulling the round rubber part off of the fin part and setting it in place on the canister first, then follow with the plastic fin part. If you don't do it this way the rubber won't seat properly and the bottom lid won't close. 10) Close the lid, replace the canister, and staaaaaart suckin like it's brand new.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi. Bought a M3888-3 Royalcylinder vacuum from Lidl. Lost manual that came with it. Only had it 4 mths. Need new hose. Plastic hose has snapped near whereit attaches to metal hose. Can I get a replacement hose from somewhere in U.K.? I know the vacuum is from Germany.


... Royal Vacuums

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?


I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums

My Infinity Shark vacuum has lost suction. The pitch sound changes very soon after turning it on. I believe the lower hose is clogged, and I cannot get the body cove unattached where the hose bends upwards into the chamber. So much for their claim of never losing suction!


... Vacuums

I have a dyson 07. Vacuum works fine, great suction using the hose. How do I switch to using the carpet vacuum. (I lost my instruction book) Thanks


If this unit has a suction hose built in to the handle, the carpet vacuum should start working after you return the handle hose to the proper position. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC07 and it has lost suction. I have checked the belt, cleaned the circular filter and emptied the dirt chamber. The hose still has plenty of suction but I can't use the hose the vacuum the entire house.


Here are some things you can check.First you need to see if the problem is with the suction or agitation.If the suction on the hose for using the attachments is low you either need new filters a new cyclone(they are not cleanable) or it is clogg ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We bought our Kirby less than 5 years ago and lately are not happy with it....it keeps breaking. The warranty has expired and our biggest complaint is that it has lost it's suction power. All the contents stay in the hose when I vacuum out the car or upholstery and it does vacuum well at all. The Kirby store quoted us over $200 to fix/ service it. Apparently this is not covered in the free yearly maintenance which we just had done. Any suggestions?


\012 Hi there,\012Well I do have a suggestion though you may not like it use it as a boat anchor.....no no I am just kidding. I have sold vacuums for 20 years and Kirby has b ... Kirby Ultimate G Bagged Upright Vacuum

I have lost the manual and forget how to use the hose part of vacuum, also the handle turns and is not secure ( that is the handle in the upright position). It is a bagless Stick Shark Vac. I need to know how to attach the hose to the vac so I can clean furniture and corners.


... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.


Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

While cleaning, the vacuum sucked up a nail and I suspect it may have punnctured the hose from the vacuum base to the uppper cannister. The reason is that it appears to have lost its suction power and nothing gets into the fliter cnnister area any more. How do I replace this part ?z?


You will have to basically split the vaccume in half to gain access pulling the plastic covers off.usually philips head screw/ ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.


TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum

My Kirby vacuum lost most of its suction. .. The hose attachment is clear, the brush attachment the same.


... Kirby G6 Bagged Upright Vacuum

My versatility electrolux vacuum is 2 years old and it has lost its suction, i have replaced the filters and checked every hosing area i have access to, it seems to all be clear. I dont know what else to do, it has a higher pitched whinnig sound when it is on


It sounds like the fan blades have worn away until there's basically no air resistance, thus no air flow/suction. The whine is created by the motor turning at a higher speed due to lack of resistance. \015\012The fan wasn't covered by the wa ... Electrolux Vacuums

My dyson hose has lost suction - Vacuums


... Vacuums

Vacuum has lost suction and does not **** much up...either through the bottom or the attachment hose!


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Our Samsung Easy1300 canister vacuum has lost suction (even with a new bag) and there doesn't seem to be anything blocking the hose. Any suggestions as to what to check next would be appreciated!


... Samsung Easy 1300 Lightweight Compact Canister Vacuum Cleaner

I have lost suction.....what do I do? -with the vacuum and the hose!


If you've tried everything else, try this:\015\012\015\012http://www.ehow.com/how_5870417_modify-dyson-prefilter-suction.html ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.


That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

HELP! my vacuum hose is connected worng and i cant fix it!


It most likely is the belt this might sound dangerous but with the vac on its side turn it on if the rollerbrush isnt spinning change belt real easy take screws off bottom cover pull it off and the belt is supposed to be hooked around motor pulley an ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC18 which has lost suction from hose.


... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Hose is there a repair manual for the hose on this kind of vacuum?? it got clogged pretty good and I thought by taking the hose apart there was a place to take the hose out.... I thought wrong and now I have a hundred piece everywhere and no vacuum..


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

No suction vacuum won't pick up -- I've checked the bag, hose...and it seems to have no sucking power. The internal hose may be jammed (I vacuumed up a lot of shredded paper), but nothing as far as I can stick in fingers in. I don't have a metal coat hanger to slip down, but I'm afraid that might tear the hose and then the darn thing won't work anyway. :o(


If it is plugged, try using a tape measure, i know it sounds stupid but it will work to unplug your line and will not tear your hose.. ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0678 seconds