Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

All the suction has been lost at the bottom end, the hose still works and sucks fine. what can be the problem? there doesnt appear to be any blockages either


Answers :

It sounds like you must have a blockage behind the beater brush on the bottom of the v ac
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

All the suction has been lost at the bottom end, the hose still works and sucks fine. what can be the problem? there doesnt appear to be any blockages either


It sounds like you must have a blockage behind the beater brush on the bottom of the v ac ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell ProHeat 2X which releases the water/shampoo mix fine, and will suck up using the hose, but will not suck up using the main floor unit. Have checked it all out, and there do not appear to be any blockages. Help please


The vacuum on its back then look under the front where the water comes\015\012out, you will see few little round holes now the chances are these\015\012holes are blocked so get something long like a pin and poke these holes\015\012through you should ... Vacuums

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........


Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port. ... Hoover Tempo Widepath Upright Vacuum - Blue

I posted my problem earlier today that I was having with my Bissell Little Green Machine not dispensing solution, but sucked up no problem. Someone said that the most common problem was a blockage. We put hot water in the reservoir for 15 minutes as advised and it still will not dispense. The fluid is now ''dribbling''so it is better. It is just not spraying. We are able to blow from the end and make bubbles in the reservoir which shows us it is not blocked. Any other suggestions?


Okay. I fixed this on mine. Undo the screws on the handle, right by the trigger. You pull the tubes off the little valve. Push on the button and see if you can blow through the valve. If not, push a pin around in the valve (with it pushed into the ... Bissell 1720-1 Little Green Wet/Dry Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

My bissell cleanview is blowing not sucking in the base. the hose works fine and the bruch appears to be rotating fine.


Try reversing your hoses.\015\012Hope this helped.Let me know by rating meFor more help go to live chat.lenwest ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My dyson 07 doesnt **** up when im doing the carpet but the hose works fine? when im vacuming it sucks up very little and the hose part seems to be sucking up air when im doing the carpet? would this mean something is plug??? thanks randy


There is a block in the hose take lower hose of and clean ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Why doesnt my rootcycle dyson **** up! belt ok, emptied regularly, the handle bit where it sucks is fine but not the rotating brush. it sucks up fluff but not light dirt and bits. changed white pipe underneath as it was split.


There is a removable cover on the bottom of some Dysons which is like a U-Bend. On occasion this is a likely spot for blockages. Also make sure that all of your filters have been cleaned. Locate your local Dyson Customer Service from ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson Animal motor is running, beater bar is turning but very little if any suction. No suction from hose either. The inside canister is filling and moving, so there is some dirt being sucked in there. I have thoroughly cleaned all filters but not sure what is causing the problem. Any ideas?


Obstruction in the hose?\015\012Your vac has developed a hairball possibly.... when a piece of flexible media ie.... cardboard, plastic etc... gets lodged in the hose, and begins collecting hair & dust to the point it no longer has enough d ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?


Open this manual to page 18 and clean all the filters listed to restore air flow.http://www.managemylife.com/mmh/lis_pdf/OWNM/L0908343.pdf ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My roller bar doesn't seem to be working, but I checked the belt and it appears to be fine, but a bit loose. Is this the problem? dial on front to determine heighth is also very loose and does not click anymore like it did a few months ago. Any help would be appreciated. thx.


If the brush roller stalls when it comes into contact withthe carpet, it might be that the tensioner spring has broken off. This is adesign flaw in the Eureka4870. The symptoms are: 1) brush spins until it contacts the carpet then itstalls, 2) the br ... Eureka Smartvac 4870 Bagged Upright Vacuum

No suction It switches on fine, but there doesnt appear to be any suction and it heats up very fast. the tube has mild suction.


Check the tube that leads down to the brush head for clogging as well as\012 any motor or HEPA filters. If that still shows nothing, take the cover\012 off the brush head (like you're changing the belt) and look for \012obstructions in there. Usual ... Euro-Pro EP602 Bagless Stick Cyclonic Vacuum

When I turn the vacuum on, and let go of the button, the vacuum just immediately turns itself off again. I have checked the cylinder and the hose and there doesnt appear to be any blockages. Can you please help?


Hi there, \012The problem is the switch itself. It is just a really common ailment for the Dyson DC08. I h ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My vaccuum makes a very high pitched sound when it runs. I cleaned it out and checked for itms stuck in it but there doesn't appear to be anything. What is causing this problem. Other than the awful sound it seems to be working fine.


Could be a worn belt. Here is the belt you need:Bissell Pet Hair Eraser Belt ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

The Bissell Powerlifter is not sucking up the water like it used to and I can't figure out why. The hose extention works fine, the main cleaner is what is having problems.


... Bissell 16943 Powerlifter Wet/Dry Vacuum

I have a Kenmore upright progrssive intell clean. For some reason it isn't sucking when I use it to vacuum. When I use attachments they work fine, but when I plug the hose back in after using the attachments and turn it back on it makes a weird noise and I can feel air blowing out of the back. Can you help me resolve this problem?


You have the answer and just don't know it. You are there so keep looking. Somewhere between where the suction hose connects with the lower hose and the power-head. There is a blockage, you may need to turn the unit upside down and look there or try ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Water suction My Bissell Proheat Clearview is not sucking up water into the tank, motor appears to be fine


Here's what I did. On the top of the water bucket there is a red oval screen, remove and clean the screen and replace. Also, next to the screen is an oval opening which meets up with a black oval gasket on main unit. Inspect the gasket and replace if ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

No suction vacuum working fine and suddenly, no suction at all....what could be the problem? no suction through the machine from either the wand or the floor/brush side


Sucked up a sock?? No seriously.. it may be as simple as that or that an on board filter is clogged. Check your manual for all filters and Hepa/screens and others. Also, is the unit making any odd noises since the non -suction scenario? Whining or s ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My kenmore progressive canister vacuum brush won't spin. I've checked the belt and it is fine. I've hit the reset button and there doesn't seem to be a problem there either.


... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

My vacuum seems to be having problems with sucking up and keeps cutting out. I have checked it and there does not seem to be a blockage anywhere


... LG Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0579 seconds