Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Help, the brushbar on my Dyson DC07 vacuum quit rotating. Belt seems to be ok. How do I fix this?


Answers :

The belt may seem okay and intact but it can be stretched. If it is stretched then it will not turn the brush when it is on the carpet. Here is the belt you need:

Dyson DC07 Belt
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Help, the brushbar on my Dyson DC07 vacuum quit rotating. Belt seems to be ok. How do I fix this?


The belt may seem okay and intact but it can be stretched. If it is stretched then it will not turn the brush when it is on the carpet. Here is the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushbar not rotating but vacuum has suction - belt not broke


At the point where the shroud is around the drive belt of the motor there is a screw that has to be remeoved. It is accessible through a hole in the housing that is inset about 3 1/2 inches. Once this is removed along with the 2 screws at the base ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Dyson DC07 brushbar is not rotating. I have checked for obstructions. The belt is intact. Is there a reset somewhere within the internals of the unit?


There are two belts on the dc07 one for the brushbar and one for the clutch this video will show you what you need to do ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Floor tool wheel will not revolve on dyson dc08 origin vacuum - seems to be jammed. How do I disassemble the unit to fix the problem with the wheel. Everything seems to be clicked in. I do not want to force anything - I might just break it. Any help will be appreciated. Thanks.


Hi,The wheels on the floor tool get junked up with hair pretty quickly, at least they did for our Dyson. The metal peg that holds them in has grooved teeth to prevent it coming out easily, but it will come out if you get a claw hammer an ... Vacuums

Bristles quit rotating and smelled like something was burning. It isn't the belt that turns the bristles. Can't afford a repairman, can you help me fix it?


Belt can reamin intact but still jam and burn. It won't necessarily break. I suggest you remove the bottom of the vacuum where the bristles spins and where the belt is located. You may have something jammed in there. You may need to remove the bristl ... Bissell 6594 PowerForce Bagless Upright Vacuum

I HAVE A DYSON DC07 I HAVE CHECKED ALL HOSES AND PLASTIC ATTACHMENT SECTIONS , CANNOT FIND ANY BLOCKAGE ANYWHERE IN THE SYSTEM .THE BELT IS GOOD AND THE BEATER BAR IS ROTATING WELL , BUT THIS VACUUM WILL NOT PICK UP ANY THING. I DID NOTICE THAT THE HEPA LIFETIME FILTER IS BLACK AND NOT SURE IF IT CAN BE WASHED OR CLEANED. THANKS BOB!


I have just cleaned mine just a half an hour ago - SAME PROBLEM !!\015\012ok take the dust cylinder off the vacuum cleaner and take the plastic clear cylinder off - there is a clear clip one side and you might need a small knife to unclip other ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Hello. My dyson dc04 keeps making a loud screeching noise when im vacuuming. It seems as though the plastic from the brush is catching on the plastic on its holder either side of the belt. Is there any way of fixing this problem?


Remove base cover by 3 'screws' 1/2 turn anti clockwise and clean well remove fibres replace cover and re try. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Seems the belt is not turning. what to do ? - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


\015\012Flip the unit over and turn it on. If you physically see it turning then the belt is fine. If it is not then you might have to have your clutch replaced ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07: When I first got this vacuum, it was so powerful that it lifted my area rugs off the floor. It is so weak it barely works. I have removed and cleaned the filter, but I can?t seem to improve the suction. What am I doing wrong? How do I fix it?


Hello,\015\012\015\012If your vacuum runs but still leaves dirt behind, the culprit could be the drive belt or an obstruction. If the agitator brush slips or won't turn, the belt is bad and needs to be replaced. If suction is weak when yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.


... Vacuums

Change belt on dyson dc07 animal - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do you change a belt on a dyson DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


Turn vacuum over so you can see the brush.\015\012Using a standard screwdriver, undo the three fasteners just behind the brush.\015\012Remove the base plate.\015\012Remove the belt.\015\012Remove roller brush.\015\012Pla ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please


... Vacuums

How do I change belt on dyson DC07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??


... Bissell 3510 PowerPartner Upright Vacuum

How to fix a new power cable to a Dyson DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


Try this site: http://www.sparesaver.com/help-and-support/dyson-sec ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1666 seconds