Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.


Answers :

If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the other a few times. If that doesn't help, the clutch may need replacing.\015\012
\015\012It may also be that the bearings at the ends of the brush bar are worn or dry. That can make a terrible noise (although most people call it squealing). Remove the brush bar, pull the bearings off both ends (one at a time, so you know which is which) and clear any entangled hair from the spindle. When you're sure it's clean, use just the smallest drop of oil or grease and reassemble. If the bearings are badly worn, that solution won't last long (if at all) and you'll have to get a new brush bar.\015\012
\015\012I hope this helps. Any further questions, just post a reply here and I'll get back to you as soon as I can.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.


If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!


... Hoover Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

My model 4870 Eureka type K Vacuum Cleaner won't turn back on after it started smoking. I turned it off, checked the belt and filters, and they seemed to be fine. The brush will turn so I don't think the motor is seized up. where do I go from here? Thanks for you help, David Andrews


... Eureka Smartvac 4870 Bagged Upright Vacuum

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.


... Kenmore 27815 Bagged Canister Vacuum

Kenmore 23613 The vacuum when turned on has a burnt smell. My husband has taken the vacuum apart, still can't seem to get to the belt. The belt in the rug part is not the problem, it is something in the canister part. Can you tell me what you think might be our problem? Thanks!


If it smells like burnt plastic it is something wrong with the motor part, but if it is a wet dog,burnt hair gross kinda smell it cool change the bag and buy deoderizer tablet to put under bag kinda like a airfreshener. if it dont work like it used ... Kenmore 22085 Bagged Canister Vacuum

Even if the flat belt is broken and the v belt loose shouldn't the shafts or something be spinning when I flip it over and turn it on? Nothing is spinning on mine


There is a tensioner pulley that drops when you drop the handle down. It squeezes the belt against the roller making it spin. This part often breaks as well. Replace the flat belt, and check to make sure the v belts edges aren't rounded. If they are ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I am trying to get to the belt on my fantom cyclone xt, although I am unable to see any screws to remove. I took the rubber bumper off thinking this would be of some help although nothing there either. Can you help???????


Remove the lens covers, bulbs and the foil. under the foil are two screws. remove the screws and the cover lifts off. the motor for the belt is held in with one screw. ... Fantom Vacums Cyclone XT Upright Vacuum

I have a bosch bagless jet 12 amps/1450 W which I got secondhand. the switch to operate the powerhead (the rug brush) no longer gives me any results. I don't have the right tools to unscrew the plates and look for a belt. I don't think it's a belt problem anyway because I don't hear the powerbrush motor turn on, either.


... Bosch Vacuums

How do i remove the canopy of my hampton bay ceiling fan? I want to relocate it and there are no screws or nuts visable on the outside. I've tried turning both ways and it gives a little but the whole fan moves when i turn it. I've tried pulling down even prying it from the ceiling. Nothing works. HELP!


HI!!\015\012\015\012I assume you've removed the blades. so next step is to check the canopy. The Ceiling Fan canopy has a decorative ring RIGHT against the ceiling that covers some screws. Remove the ring, remove the screws ... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)


I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My eureka Hello im not sure what kinda of eureka it is a friend gave it to us...and I went to change the bag and vacuum and the spinner isnt going...and i dont think its the belt...help please! i looked on the back and it gave me a modle number its 4475


The belt may look ok, but am sure it is stretched and when this happens, the brush roll won't turn like it should. Did you check the brush roll ends to see if they turn freely, if not replace it. ... Vacuums

It is making a racket when i turn it on. I took the brush off and cleaned it it is not the belt i don't know how to take the cover off the top front so i can look near the motor can you help please. [email protected] .com Thank you Staci Bishop


These units have two screws that hold the "hood" in place. With the belt/brush roll cover off look on the underside for the heads of these screws. Once these are removed the top should come off. ... Hoover U5096-930 Bagged Upright Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt


Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0975 seconds