Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Loss of performance, belt seems ok filter is clean

Answers :

The lifetime pre motor filter could be blocked, dust filter (Blue) in the circular housing end of motor housing. or the machine air intake is blocked or the cyclonic chamber needs removing and cleaning. All of the bits not silver grey can be removed take them off and clear out the tubes. If after this it has still got the lack of power the motor may be on its way out (but you would be able to smell it burning) hope this helps
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loss of performance, belt seems ok filter is clean

The lifetime pre motor filter could be blocked, dust filter (Blue) in the circular housing end of motor housing. or the machine air intake is blocked or the cyclonic chamber needs removing and cleaning. All of the bits not silver grey can be removed ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?

Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Why does my dyson slim dc18 keep shutting down, even though i keep it clean. Filters area is clean and all others have been properly blown out with air from a air compressor. It will work for about 5-10 minutes and then shuts down. Smells like ****, check the belt and a bit later it restarts again. It's seems to be almost over heating.

Maybe your motor is going. Here's a link to a site that talks about motor failure and replacement in a DC07 (not DC18). I don't know exactly what the odor smells like but maybe you can see if you have any of the other symptoms. Good luck! ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

My Bissel Proheat smartmix bottle is emptying really fast and it doesn't seem like the carpet is even getting wet. I am just trying to do a rug in the kitchen and have filled the smartmix bottle 3x now and the rug is barely wet yet. I have cleaned out the flow indicator filter and it does not spin when I push the button like it used to. I have also checked the belt and it seems fine. It is actually a Bissel Proheat 7901/8910 (Pet) but they could not find my product. Any suggestions, I am

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Rollar is not turning. Belt seems to have tension. Does not **** anything up off of the floor. Filters are clean but when we turn it on, the roller is not turning or sucking anything up off the floor.

Hi Susan,I'm sorry to hear you're having difficulties with your DC07. It's probably best if you get in touch with us directly so we can determine which model of DC07 you have, and run through some troubleshooting over the phone with you. You ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t

... Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

The performance indicator light will not go out. I have cleaned the bag, filter and hose. there does not seem to be enough suction.

You are clogged somewhere ... \015\012\015\012no suction? \015\012performance indicator says no suction?\015\012\015\012find and remove the clog.\015\012\015\012id be looking in the hose about 4 inches from ... Vacuums

Major loss of suction in my dirt Devil Dynamite. I have changed the filter, the belt and cleaned the hose....any suggestions?

... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Noticeable loss of suction, the filter has been cleaned

Your link doesn't work CHRISPURS1 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano

... Electrolux Vacuums

I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.

... Dyson DC25 All Floors Bagless Upright Vacuum

Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don't). I re charge the power, and all seems fine and then it goes back to wanting the filters cleaned. The suction is also not working to full capacity.

Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there ... Vacuums

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

I am getting a lot of dog hair on the filter after cleaning one room, this is something new. I cleaned as many parts as I can. It seems like the dog hair is moving from the clear canester onto the top of the filter, any thoughts??

The cone in the tank has a black gasket make sure it hasn't slid to far up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

It seems to be blowing dirt around not suking but when removing the attachment to clean stairs etc the pipe works fine have washed filteR ? SLIM UPRIGHT DC ALLERGY 18. Have cleaned out filter emptied cylinder taken any bits of cotton or hairs from brushes..........

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Def no choked probs, as I check and clean filters regularly, but when switched on there seems to be a short whineing sound before returning to normal, and def wont lift fluff etc., just runs over it, although ther seems to be a fair amount of suction. It does clean but not properly

Hi, this is Jack at Dyson.\015\012\015\012You should be able to resolve your problem by following these simple steps: http://www.dy ... Dyson Ball DC24 Bagless Upright Vacuum

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen

Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

Dosenot seem to clean the carpets as good as before, we have cleaned the filter and keep the canister cleaned. What else might it be; I bought it for the express purpose to clean animal hair off my carpet?

Hi there,I'm sorry to hear you're having difficulties with your DC17. This machine should have no problem dealing with animal hair, so if it doesn't seem to be picking up as well as usual, this may be due to a blockage. The easiest way to che ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?

... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

I have a Kenmore central vacuum cleaner model number c107 34601. We have emptied the bucket and shaken the filter out to clean it. There is a filter that is filthy so we shook it out into a bag but the cleaner still seems to not have great suction. I notice there is a similar cap to the outlets I plug the central vac hose into on the unit itself that doesn't power the nozzle when used. 1 - what is this for? 2 - Should I somehow remove the entire filter and if so - can you tell me step by step ho

... Electrolux Vacuums

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.

My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

My filter is always full of dog hair on my animal. What is causing this. I have to clean the filter each week . Dirt seems to always be trapped in the filter also.

I have same cyclonic as you.  I also have a Miele Pull-along.  I use the cyclonic for fine dust after picking up the hairs with the Miele.  Much quicker in the long run.  Otherwise I would waste a lot of ti ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0963 seconds