Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?

Answers :

Need replaced Clutch Assy and Brushbar
\015\012Clutch Assy part no:900252-04
\015\012Brushbar Assy part no:904174-01
\015\012try cleaning all Hose
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?

Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush not spinning , no belt is needing to be replaced, i think something in switch, cause before this problem the switch was always on , i would plug/unplug to turn it on. thisis case with 2 vacuums i have

... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym

Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Belts can i tell if i need new belts just by turning the vacuum on it's side and looking underneath, or do i need to unscrew/remove a part to see.  thanks

Yes you can. belt goes round the brush roll and is in view. also turn on and see if the brush roll rotates. if belt is broken then no rotation ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01

... Vacuums

My Eureka The boss Smartvac Model #4870 roller brush won't turn even on the highest setting and the belt smells hot. we took the belt off. How can you tell if it needs replaced?

Just by what you explained I can tell that it needs to be replaced. The belt doesn't have to be broken to need replacing, if it is stretched and worn then it will slip on the motor shaft and not turn the brush roll and get hot. Here is a link to the ... Eureka Smartvac 4870 Bagged Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I cannot seem to replace the beater bar on my Dyson - it seems to spin OK, but when I turn the vacuum back on and turn it to the 'Carpet" position, it makes a noise that is unbelievable. What's up with that? The belt is intact.

Sounds like its the clutch to me if it sounds like a rapid clicking and you have a large knob on the side of the cleaner head it is going to be the clutch this is a hard part to changed without the know how to do it and it is very easy to break the o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I just put a new belt on my boss 4800 and it is to loose? Does the beater bar needed to be replaced? There is no traction to turn the belt, it spins

Sounds like the belt is to big you didnt replace with the correct belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

The small belt that makes the beater bars spin broke. It is only two years old; repair shops tell me this involves replacing two belts because of some kind of clutch to the tune of $150! Is this possible to repair myself

A very easy replacement. The belts cost about £3 each. Yes, there are two belts and even if the clutch needed replacement, this is about £20 for clutch and both belts http://www.dysonpartsdirect.co.uk/dysonparts/dc07belts.shtml - this is ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance

The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.

You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???

The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Dyson dc07 makes loud noise when on carpet setting bar does not spin, could clutch need replacing?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1775 seconds