Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

We have a dc04 and the belt keeps breaking as soon as we turn it on. Have u any ideas as we have took it apart and we think cleaned all parts

Answers :

If the brush roller is sticky that will put a strain on the belt check it can turn freely and also the brush bearings are free
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a dc04 and the belt keeps breaking as soon as we turn it on. Have u any ideas as we have took it apart and we think cleaned all parts

If the brush roller is sticky that will put a strain on the belt check it can turn freely and also the brush bearings are free ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!

That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

Took my Hoover Steam Vac apart to clean it and now it won't **** up the water but was working fine before I got the bright idea to clean it. Took four screws out but did not touch the motor. It puts out water and the brushes rotate but no suction? Thank you for your help, Cathy

The suction is created by the motor and is pulled to the motor through the flexible hose. The hose could have pulled off at one end or it could have torn in a spot where there is more pull on the hose like when you lay the handle down to empty dirty ... Hoover F7431-900 SteamVac Vacuum

Kenmore 23613 The vacuum when turned on has a burnt smell. My husband has taken the vacuum apart, still can't seem to get to the belt. The belt in the rug part is not the problem, it is something in the canister part. Can you tell me what you think might be our problem? Thanks!

If it smells like burnt plastic it is something wrong with the motor part, but if it is a wet dog,burnt hair gross kinda smell it cool change the bag and buy deoderizer tablet to put under bag kinda like a airfreshener. if it dont work like it used ... Kenmore 22085 Bagged Canister Vacuum

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.

Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.

Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b

... Vacuums

Bag was not on good, resulted in dust,dirt, dog hair everywhere...have cleaned pretty thoroughly but vacuum does not have any suction. After taking apart did find that the larger wide belt is broke but I think that just affects the self propel...is there a belt tied to suction? HELP!

Greetings from GoVacuum,\015\012\015\012There are two things that you should check on this vacuum after running it without a bag inside. The first thing you should check is the filter that is underneath of the vacuum bag. This filter i ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Carpet stained recently cleaned my cream coloured carpet in my entrance hall with a carpet cleaning product, wet foamy spray type, ran out of this and found a part bottle of a different brand in my cupboard, used this to finish off however must be some sort of reaction and carpet gone a greenish colour i think (colour blind sorry ) any idea's of any product that might restore my carpet, will try anything, nothing to loose. thank you Peter McGurk Goole East Yorks

Ok in the future try to have carpet cleaned only by a pro. For spot cleaning use white paper towels or dish towels and warm water. (ONLY WHITE) 99% of fabric is white and then dyed to color and if you use a color cloth you might pull the dye from the ... Bissell OxyKIC - Oxygen Activated Carpet Spot and Stain Remover Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.

... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Oreck 9100 Xl blowing out dirt instead of sucking in. Took apart,cleaned & checked belt

... Oreck XL Ultra Bagged Upright Vacuum

I took apart my bissell easy vac to clean it because it was clogged and now I cannot remember how a part goes on that is underneith the vacuum. I keep putting it on but its not right. It lifts the vacuum off the floor so it is not sitting in there right.

Make sure the plate is lined up correctly it should side down flush ... Vacuums

I bought this vaccuum just a few months ago. Now it barely sucks anything up and it is making this very loud noise. It almost sounds like the brush is going to vibrate off. I keep thinking something is stuck in it, but I took it apart and everything seems normal. It did melt a couple of belts also.

Probably the motor is jammed or the part where it sucks up stuff its full ... Bissell 3590 CleanView Bagless Upright Vacuum

I cleaned the roller on my Dyson DC 07, and after reassembly, it makes a sound like the belt is being chewed. I took it apart a couple times, goes back together fine, but still makes the noise

Hi its Darran at Dyson. \012\012Your machine is designed to make this ratchet noise if the brush bar is \012obstructed. We would recommend checking the brush bar and soleplate \012area and removing any blockages or hairs/threads that are ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

I have an older Wega 2 group espresso machine. Looks like a date of 1992 on the group head, but not sure. This has no model name that I can find. Anyway, when I turn it on I get all lights flashing after it heats up 5 minutes or so. I do get nice steam from the wands. I drained teh tank and found a little scale, but not much. I took apart the group heads and cleaned them thinking it may be a clog there, but that doesn't seem to have worked. Also fwiw the water level float is not visible and whe

For a new fridge, need more time to maintain the required temperature of the fridge abut mainly the goods in it? So everything seems normal. The time will be reduced day by day since the goods will stay for longer time in and door opening will bec ... Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if

... Vacuums

Bissell cleanview 11 bagless special edition model 3576-2 I took apart to clean the filters and don't remember howto put the bottom of the dirt container back. I thought I put the empty container back in place correctly but the dirt when vacuuming is flowing through another part of the vacuum.

... Bissell Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?

I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum

I can't get the brushes to rotate on my hoover steam vac v. i took them apart and cleaned them and they still wont work. any ideas?

Scrubbing brushes are driven by a belt. The belt either broke or slipped off its pulley. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????

Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0958 seconds