Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Pipe valve on dc07 same as one on dc 17

\015 Is pipe valve on dyson dc07 same as one on dc 17\015

Answers :

Hi there, the parts are not interchangeable, but you can purchase a replacement valve pipe for your machine via our website at www.dyson.com.

Kind regards
Darran
Dyson Customer Service
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pipe valve on dc07 same as one on dc 17


Hi there, the parts are not interchangeable, but you can purchase a replacement valve pipe for your machine via our website at www.dyson.com. Kind regardsDarran Dyson Customer Service ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac


Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?


Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My manual says it is DC07, but it is pink and silver in colour. I have 2 problems, firstly the brush has stopped spinning, but belt appears intact. Secondly there are tiny holes in suction pipe near brush i.e. the little section of suction pipe at base of vacuum cleaner.


Hi there, \015\012The DC07 came out in a few different variations so the colour only indicates that yours has a hepa filter. The first problem can be caused by a few different things\015\0121. the brush roller bearings are worn or siexed. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell Receiver Autoload ProHeat 8920 Is this valve a one way check valve?


... Bissell 8920 ProHeat 2XTM Upright Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

Delonghi ECO310 BK espresso coffee maker. The unit is leaking from the steam solenoid valve on top of the boiler unit. The Teflon pipe that's retained by the clip is not a tight fit and is able to slide in/out slightly. There is a red gasket present, that sits over the tube, but I suspect that there may be someting else missing from the assembly because of the play in the pipe. Does anyone have a an exploded diagram of the assembly or can confirm that it is just the gasket that is likely to h


... Vacuums

Have a windchaser portable ice maker which only makes one cube at a time. I have been told one possibility is a clogged freon tube, but no suggestions on repair. Another is low freon, but I cannot find a fill valve. Any suggestions?


CAUTION !!! ----freon re-charge should be performed by a trained service person -- this can be very dangerous if trying to perform yourself.\015\012depending on the year of the unit --one thing that I would check is to make sure you have good a ... Vacuums

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi , I have an Electrolux powerplus 1800 hoover Z4492 the hose that attaches to the telescopic pipe snapped and tried to get out the grey plastic out in one bit but it snapped ..if i got another telescopic pipe would it come with the grey tube that sits in the hole to keep the hose in place ?


... Electrolux Vacuums

The valve pipe assembly just popped off our Dyson DC 17. How do I get it back on? I see it appear the arm of the assembly needs to be captured but I can't figure how to get it all lined up without forcing it together.


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

No suction to pipe tool - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Your hose is blocked up get a wire coat hanger down the hose ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Got pipe out - can't get it back in - Dyson DC07 Bagless Upright Cyclonic Vacuum


The pipe should have a plastic holder at the bottom of the hose, providing its still in tact.\015\012If it is then do the following:\015\0121 take the wand off the hose so the hose is bendy\015\0122 the plastic holder at the bottom ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Cannot reinstall valve pipe assembly on Dyson dc17 vacuum


Take off the cyclone canister and flip open the filter cover. (The U-shaped tube at the bottom of the vacuum is probably already off-if not, release the lock with a screwdriver and remove it.) Release the vacuum from the upright positon, so that the ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.


Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Cannot re-install the valve pipe assembly? - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have changed the side filter on my DC07 - Is there another one under the bin and if so, how do I get at it?


Yes there is one under the catch canister. When you remove the canister you'll see a hinged plate. There are a couple of tabs you need to pry to get them loose. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My miele hoover was working one minute then switched it self off, bag not full, but warning light on hoover, no blockage in hoover pipe what next


Is this a Miele or a Hoover? What is the model number. Need to know if you want help. ... Vacuums

I'm doing an engine rebuild on a 1986 Mazda Familia (*** import) BFMR B6 engine 16 dohc turbo. I'have no idea where all the vacuum pipes go. It has a blow off valve and a turbo boost control fitted. The car was bought by my son, a typical teenage boy racer.


Your post needs to be reposted in the automobile repair section, this is for vacuum cleaners. ... Vacuums

I NEED A TELESCOPIC HOSE FOR MY PHILIPS EXPRESSION HOOVER, WHERE CAN I GET THIS MY HOSE PIPE IS BROKEN AND I HAVE TRIED TO GET A NEW ONE AT VARIOUS SHOPS HERE IN IRELAND AND I CANT.


Hi - greetings from Scotland!\015\012Im not sure if you mean telescopic hose = do you mean telescopic metal tubes? If so they are readily available on ebay.co.uk I buy from many sellers on there but Hoovermania are one of the best. \015\012\015 ... Philips Vacuums

Hi, I have a Hoover Hotshotz vacuum cleaner, The plastic connector that joins the hose to the chromed metal pipe has broken. Any idea were I may attain a new one? I live in Perth. Regards Gary


Hi there Gary, SmartAlec from NelsonVacuums.com.au here. I can help you with that but first i need to know if you have the newer hoover hotshotz (less than 5 years old) or ... Hoover Vacuums

I have a DC07 Animal and the roller stopped rolling. I appears that the roller sheared off on one side.


Your belt could be torn or the teeth could be worn off. Contact dyson for a local repair rep. ... Dyson Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0311 seconds