Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

The vacuum works well. The brush does not spin

\015 The vacuum works well. The brush does not spin and the belt is not broken. What do I look at next\015

Answers :

Hi its Darran at Dyson.

If you have a brush control, make sure that its in the centre position when its stood upright and then try releasing the head to put the machine into the vacuuming position and see if the brush control dial moves forward to the on position and that the brush bar is turning.

Full details on these checks can be seen on our site at www.dyson.com in the support section.

I hope that this information is useful to you.

Kind regards
Dyson Customer Service
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.

Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.

- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

Luv300b vacuum brushes won't spin. The belt is fine but still not working. Any suggestions?

... LG Electronics Kompressor Plus Upright Vacuum Cleaner LUV300B

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

How to repair BEAM Central Vacuum Power Brush. Motor works perfectly, belt brand new but unable to spin brush.

... Vacuums

The vacuum works well. The brush does not spin

Hi its Darran at Dyson. If you have a brush control, make sure that its in the centre position when its stood upright and then try releasing the head to put the machine into the vacuuming position and see if the brush control dial moves f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My carpet cleaning brush does not turn on. The vacuum cleaner works fine but the the carpet cleaning attachment does not get any power so the light does not come on & the brush does not spin

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

I was vacuuming over some fringe and then the brush just stopped working and there is nothing caught in it. It spins freely when twisted by hand, but will not turn when vacuum turned on.

Have you checked the belt? it could have snapped when you caught the fringe. also if it has a separate brushroll motor there should be a reset that probably tripped out. ... Vacuums

Roomba Discovery My Roomba Discovery seems to work fine, mechanically, but it no longer seems to collect any dust. (The collection bin remains empty after the Roomba has circulated around the floor for quite a while). The brush has been replaced and spins normally. Does anyone have an idea why this machine's vacuum function no longer seems to work? I would appreciate any feedback. Jeremy

Did you replace the filter? when you remove the dust bin there is a small filter that needs to be cleaned, or replaced. You can buy a maintenance kit that replaces the brushes and filters as well, its good to replace them all regularly ... Roomba Robotic Floor Bagless Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?

Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum

I have a hoover windtunnel upright vacuum bought it a few months ago and now the brush spinning stopped working.

You probably have a broken belt, or the belt came off. The Self Propel Windtunnel has an issue with the pulley that tightens the V-belt in place getting stuck and needs to be taken apart and released, but most l ... Hoover Vacuums

Spin brush isn't working - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover f7450100 spin brush will not work - Hoover F7431-900 SteamVac Vacuum

... Hoover F7431-900 SteamVac Vacuum

The motor is working but brush not spinning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC07s have two drive ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My eureka optima vacuum shuts off after 5 minutes of use, the brush still spins, but no suction. If I wait 30 minutes, it will work again, for 5 minutes.

... Eureka 431A Optima Bagless Upright Vacuum

Kenmore Beltless Vacuum brush will not spin. Everything else works.

There is a reset button on the side of the lower base of the machine, plug in the unit turn on the switch to the brush and vacuum are both engaged hit the reset button, remember the roller will not engage when the handle is in the upright position, r ... Vacuums

The brushes on the Hoover F7452-900 SteamVac Upright Vacuum will not spin but everything else seems to work fine. How can I solve this problem?

There is no belt. This unit uses a turbine that uses air off the vacuum motor. There is an actuator arm that moves rearward when you depress the handle release and then lower the handle to use the vacuum. That engages the turbine and spins the brushe ... Hoover F7452-900 SteamVac Upright Vacuum

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?

Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0878 seconds