Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Power Button won't stay down/on.

\015 I push the power button down, but it will not stay on.\015

Answers :

Hi There,
\012Most likely your switch has gone bad, and you'll need to replace the \012on/off switch on your Dyson DC07. If you have to hold down the switch in\012 order to keep the vacuum on, this is indicative\012 of needing a new switch. Unfortunately this is very common problem on \012the Dyson vacuums2_bing.gif . \012The switch that Dyson uses for their vacuums is one of the cheapest switches\012 on any vacuum on the market today. The good news though is that this is\012 not a extremely difficult repair to fix.

I took pictures of \012replacing the switch assembly on one of our customers repairs they \012brought in. It was having the same exact problem that yours is, it just \012wouldn't stay on. Here's how you can fix the switch on your Dyson:

-\012 T15 Torx Bit Screw Driver
- Genuine Dyson DC07 & DC14 Replacement On/Off Switch \012Part 901181
- Needle Nose Pliers
- Patience (haha)

The \012switch above is actually a link back to our site if you have yet to \012purchase the switch yet. We carry most every Dyson part.


Step 1. First thing you'll\012 want to do is to unwrap the cord from the machine, and remove the \012handle from the upright part, then slide the hose all the way down the \012wand, and remove the hose from the handle assembly completely and set it\012 aside. Also remove the dust bin assembly completely from the machine as\012 well.

Step\012 2. Once you've remove the handle from the machine I find it easier to \012work on if you lay the vacuum \012on it's back, with the switch button facing upwards. Now remove the T15 Torx\012 bit screw that is directly below the switch actuator. I have circled \012the location of this screw in the picture below:

Step\012 3: After you have taken off the screw, you're doing to need to remove \012the switch box housing from the vacuum that the screw was securing. \012Simply use your flat head screw driver, and pry the two small arms \012upwards. Be careful when prying, the plastic components on Dyson Vacuums\012are really cheap quality plastic, and I can't tell you how many times I \012have seen these plastic parts break when customers bring in repairs to \012us here at govacuum headquarters. Here's a picture of the location of where you should pry the \012switching off:

Here's\012 what the vacuum should look like after the switch housing has been \012removed:

Step\012 4. Use your needle nose pliers to remove the terminals from both of the\012 switch poles.


Step\012 5. Take out the new switch assembly. I find it the easiest to use my \012needle nose pliers to reattach the wires to the new switch, but it also \012can be done with just your hands. Both both wires to your switch. If the cords have\012 come loose while you have been working on the vacuum, you'll need to \012put the wires back into their proper places as well. This is how the \012switch and the wires should look like when you're done:

Step\012 6. Once the switch and cords are back to their normal places, simply \012put the switch housing cover back on, and screw in the one screw.

I\012 hope that this repair was helpful to you, if you have any questions or \012have any problems, please feel free to use the clarification request \012form here on Fixya.

If you ever need any for your \012Dyson, we do carry most parts and accessories on our site under our Dyson Parts Section .

If this was helpful, please be so kind and leave feedback for the repair. This is really, really appreciated and is the reason repair professionals like myself continue to post free repair help on Fixya rather then just answering the paid questions.

Thanks \012again,

Chris J.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Power button wont stay on. have to hold the power button manually for it to stay on.

Most likely you have to replace ON/OFF switch. look at detail instructions how to do it on our website:http://www.goodvac.com/kb_results.asp?ID=18 ... Kirby Ultimate G Bagged Upright Vacuum

My dyson dc14 wont stay running. if you hold power button down it runs. cleaned filters and brush and the belt is not broke. any advice on solving the problem?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

When i hit the power button on my miele carina, it doesnt lock and stay on. i have to hold down the power button for the power to stay on. Please advise

Try a little WD-40 sprayed sparingly on the button. work the button a few times- may be sticky spring or contact. if that doesn't work, check with retailer where you purchased it- see if you can get a replacement switch! if you're handy, or have a ha ... Miele Carina Vacuum Vacuum

I have a miele S712 (2 yrs old worked fine yesterday) - I had been doing some diy work inside and had the vac on just to reduce some of the dust in the air - after a while the vacuum fizzled out. I guessed it had overheated and took it outside to cool down - when I tried to turn it back on pressing the power button gives it power and it starts to **** but it won't STAY on, soon as you release the power button it stops, and the orange bag indicator is showing full. As I have a compressor I took

You have got dust in the micro switch and it is not latching on, if you look at this and clean it, that will solve your problem, however blowing the motir has probably wrecked the motor bearings. ... Miele Vacuums

Wont stay powered on

He is right - some parts for these are near impossible to find..\015\012\015\012Did he mention what parts are not obtainable ?\015\012\015\012This is a decent site that has allot of parts available -- ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Bissell 5770 vacuum power won't stay on. The power will only stay on if you hold down the button the whole time.

I just had this happen to me. I took the top part of the vacuum off, unscrewed all of the screws from the top piece and opened it just enough to pop off the plastic red power button. Then I pressed the switch mechanism up and down a few times to rese ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

My roomba wont work. Pushing the power button doesnt do anything. It charges seemingly normal, going to green in a few hours. ive tried the reset trick, holding the power button down with the battery removed. Now what? thanks

... iRobot Remanufactured Roomba Vacuum Cleaning Robot with Scheduler, Case/Color May Vary Robotic Vacuum

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.

Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

Hoover elite power wont stay on

Go to http://hoover.com/ and get the section support download the inst.manual, section troubleshooting, videos for guide for troubleshooting and fix it.God bless you ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Power button not engaging...vacuum will not stay

The power button is worn out and needs to be replaced. That vacuum is pretty simple. So even if you don't know how to take it apart it shouldn't cost much to have it repaired. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Miele power plus brush model seb234/236 won't work and telescoping wand wont stay xtended

... Vacuums

Start button wont stay on. Is there a trick to

Have a look at:\015\012\015\012http://www.dysonmedic.com/DC07%20Folder/DC07%20Motor%20change.html\015\012\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Power Button won't stay down/on.

Hi There,\012\012Most likely your switch has gone bad, and you'll need to replace the \012on/off switch on your Dyson DC07. If you have to hold down the switch in\012 order to keep the vacuum on, this is indicative\012 of nee ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When i push on the power button on it runs only as long as my foot stays on the on/off power switch once i move my foot it immediately shuts off?

... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Dyson DC35 beater bar stays on when power button isn't pushed

... Dyson DC35 Multi Floor Digital Slim Cordless Vacuum

Dyson will not stay powered on unless power button is continuously pressed. Is this a switch malfunction or something else?

Yes, you probably need to replace the switch - call the Dyson helpline, they'll give you the info for your closest authorized repair dealer who will open it up and replace the switch for you. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Won't retain power, only stays on when you hold power button

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My electrolux E2000, power button wont work, it doesn't click like it use to and it wont start

... Vacuums

The power button does not work 80% on the time. I have to keep flicking it on and off until it turns on. The battery is fully charged, so that is not the reason. Once power is on, no issues staying on.

... Oreck TEK100 Handheld Vacuum

While vacuuming the beater bar shuts off all by itself, the main power source stays on. I touch the power button on the beater bar to start it again and it shortly after shuts off again. why is this happening?

... Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum

My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Power won't stay on when power button pushed - Dyson Vacuums

... Dyson Vacuums

Power button won't stay on. If I hold it down, it sucks fine, but it won't stay pushed down.

Bad switch ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The power head model #116. 53812300 does not stay on. When I push the belt reset button it only stays on for a second or so. The belt is not jammed or the roller.

... Kenmore Vacuums

The microwave will not turn on. No power. Checked fuse box and power outlet...not the problem. Unit just wont turn on? Is there a reset button or another option.?

Remove the cover and locate the internal fuse you will find near the power cord entry. Replace with the same. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0826 seconds