Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?
The rotating brush is not moving.
\015 I noticed that it wasn't picking up very well. I now know that the brush is not spinning or moving at all.\015
Is the dyson brush belt-driven like most other vaccuums? broken brush belts usually cause that. they are easily replaced at most dept stoes or vac stores.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move
There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
The rotating brush is not moving.
Is the dyson brush belt-driven like most other vaccuums? broken brush belts usually cause that. they are easily replaced at most dept stoes or vac stores. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Lg luv3008 vacuum cleaner when I move the machine, the brush roller does not rotate
... LG Vacuums
I have a hoover carpet cleaner model # F7427-900 series Z120 and the rotating brushes stopped moving. How do I fix this?
The brushe until needs to be snapped in very hard; to line up correctly. Pull the unti off and put it back in, good luck. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
The shaft on the motor for rotating the brush is not moving. It is a Kenmore Whispertone 12 VModel 116 3521290. I am suspicious of the Belt Protection system.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=661780\015\012Generic problem for all Vacuums\015\012The shaft on the motor\015\012Posted by tsnater on ... Vacuums
I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.
Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum
My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz
Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum
My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?
I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum
It seems when i am vacuuming it is very hard it move and the brushes does not rotate after the rug strings got into it.
Your belt is stretched or worn and therefore cannot turn against the resistance of the carpet. If you replace the belt it will fix the problem. You can get the belt you need here: ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Brushes are not rotating, V-belt seems too loose
V-belt suppose to be loose (according the manual). I just replaces it (and was worry that it is loose), but brush rotating fine. So your problem is somewhere else. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.
If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
Cleaning brushes wont rotate
I understand how important the brushes are when cleaning. You may want to the check the pump belt for breakage for the brush belt and pump belt work in conjunction with the pump. If you're still experiencing difficulty, you may want t ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Brush not moving in Bissell pro-heat
If the belt is more then 6 months old or more, then the belt will have to be replaced reguardless of the way it lookes. belts can stretch over time and when you put the machine on the carpet the friction causes the brush to stop because the belt has ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for
Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.
If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum
F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.
Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula
There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums
Bissell Lift OfF Brush Roller Stops Rotating
They make the worst machines, the rollers are cheap and they make it so you cant take them apart to clean them. You don't want a dyson either, they aren't any better for pets. With all that hardwood floors you should get a good canister vacuum, sebo ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Miele vacuum turbo plus brush does not rotate
Hi Jeanakemi10,The front brush motor will not engage until the power is turned on and\015\012the handle is in the down position. In the upright position the brush\015\012motor wont engage. Typical faults will be the belt is broken and nee ... Miele S318 Bagged Canister Vacuum
The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up
Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums
I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,
It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle
My pet hair eraser rotating brush does not rotate. I read the manual and cleaned the brush and placed it back correctly, but it is not working when I am using it. If I lift the vacuum from the flour, it starts rotating so I think it is the matter of the amount of contact to the flour. what should I do?
... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
No matter how many new belts we put in the brush will not rotate when it touches the floor. If you hold it straight up the brush rotates like crazy. Why is the brush not cleaning the floor. Yes, I have the right belt. It is R we have the boss. 12 amps. Model 4870
There is probably an accumulation of slippery stuff on the shaft that drives the belt. You can scrape it clean with a sharp knife or a razor blade. You might need to use some kind of solvent to get it clean, and if you do, be sure to follow up wit ... Eureka Vacuums