Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

I have a dyson dc07 hoover, is it possible to replace the carry handle


Answers :

Hi thanks for contacting FixYa. My name is Don.
\012
\012Whilst it is "possible" to fix the carry handle it is a far trickier job than just buying a whole new Cyclone. For this reason Dyson do not sell the handle separately.
\012
\012I would suggest you buy the whole new cyclone. You can buy them new for around £30 £40 from Dyson or Espares.co.uk.
\012
\012You could probably get a second hand one or better still a refurbished one on eBay though. Shouldnt cost you too much on Ebay. Maybe £15
\012
\012Hope this answers your query.
\012
\012Thanks for contacting FixYa. Don
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dyson dc07 hoover, is it possible to replace the carry handle


Hi thanks for contacting FixYa. My name is Don.\012\012Whilst it is "possible" to fix the carry handle it is a far trickier job than just buying a whole new Cyclone. For this reason Dyson do not sell the handle separately.\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Handle Release Pedal Replacement--How is it possible?


If you look at the picture, the slots are right across from the drive wheels, you can see the slots in the picture. Use a flat blade screwdriver. ... Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE.


... Vacuums

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

How to replace dyson dc07 catch handle spring


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?


There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the b ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Replace Belt on hoover - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Cant lower handle on my dyson dc07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Handle on Dyson ball does not click back into position. This means that when you are hoovering the handle moves back and forth as you move the hoover instead of it being


... Vacuums

Replace power cord on Dyson DC07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


The following link will take you to an article on how to change the motor on a DC07. Look at photos 4, 5 and 6 which shows how to disconnect the power cord.\015\012\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do you replace the band in a dyson dc07? - Dyson DC07 Bagless Upright Cyclonic Vacuum


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you are to refering to is the one from the clutch to the brush bar. Unfortuenately the other belt is hi ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Replacing dyson dc07 duct assembly - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need the part # for a Dyson DC07 handle - Dyson DC07 Bagless Upright Cyclonic Vacuum


Hi there the part number for the DC07 handle is 904247-49. \012if you are in Australia you can get these from vacuumspot.\012Happy Vacuuming! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

HOW DO I REPLACE THE HOSE ON MY DYSON DC07?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)


Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We replaced the short hose that connects the sucking part to the hole where the dirt goes underneath my Dyson DC07 but now the side of the hose that needs to attach to the machine falls off.


I know the hose you are talking about it is called the DC07 internal hose. Over time the ends can stretch and perish which will mean y ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Instruction dyson hoovers root cyclone dc07


... Vacuums

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?


Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Platinum Bagged UH30010 has check bag light on after I replaced the handle. How do I clear the check bag light so that vacuum will run?


... Hoover UH30010COM Bagged Vacuum

Can you tell me how to replace the bin flap on a Dyson DC07?


Hi there, its Darran at Dyson here. The plastic is quite flexible, you should be able to locate the bin base into one of the lugs on one side of the bin and then twist it slightly to locate the other lug. If you are still havi ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Unable to find a panasonic replacement motor for dyson dc07 vac.


You can convert it to the YDK one if you get the YDK motor housing as well. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1065 seconds