Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

My dyson just stopped running while vacuuming with wand

Answers :

You probably got a blockage in your wand which caused it to overheat and cut out. Check for blockages, use a brush stale down the tube to dislodge anything. Next, check your filters, refer to the tutorials here: Looking after your Dyson.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson just stopped running while vacuuming with wand

You probably got a blockage in your wand which caused it to overheat and cut out. Check for blockages, use a brush stale down the tube to dislodge anything. Next, check your filters, refer to the tutorials here: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.

The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc16 stops running - Dyson DC16 Bagless Handheld Cyclonic Vacuum

... Dyson DC16 Bagless Handheld Cyclonic Vacuum

HELP!!dyson vacuum only 2 years old model DC18 runs but has lost suction on the wand side of the vacuum does anyone have any suggestions for us??

Its the ball cradle assembly. There is a little clip that changes the direction of the suction. that clip breaks all the time and causes the internal direction valve to stay in one position. unfortunately dyson doesnt sell these parts separate, you w ... Dyson Vacuums

My dyson dc44 just stopped running in the middle of vacuuming, I checked the battery, cleaned the head, I emptied the bin. Is there a reset button anywhere for this machine?

... Dyson DC44 Animal Cordless Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dc33 stopped running with a burning smell - Dyson DC33 Bagged Upright Vacuum

It sounds like your belt is broken. ... Dyson DC33 Bagged Upright Vacuum

Stopped running. won't turn on - Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Check power cord or replaced Powercord Assy part no : 905449-04\015\012check power switch or replaced power switch part no : 910971-01 ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn

The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.

Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

Fantom vacuum vacuum starts running fine at first,but after about 15 mins the suction stops but the vacuum continues to run

Sounds like a partly clogged filter ... Fantom Vacums FM741 Twister Bagless Upright Vacuum

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.

... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My beater bar will run for a few seconds then stop on my dyson dc28

... Dyson DC28 Animal Bagless Upright Vacuum

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.

... Broan-NuTone VX475 Bagged Central System Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!

Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

I cant remove my wand on my Dyson vacuum. - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi its Darran at Dyson. It is possible that if the hose is blocked that the wand handle may become jammed. For help releasing this, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US) and one of our advisors can talk yo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The Oreck vacuum motor sparks the stop running. Plugged to another outlet, the motor did the same things, run for few seconds with sparks and stopped again.

... Oreck XL2200 Bagged Upright Vacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.

I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dc16 dyson root vacuum stopped working abruptly with no indication of a weak battery, the charger does not show a charge on battery. usually the vacuum slowed before it stopped with a dead battery, any suggestions

... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Dyson dc40 vacuum stopped working

... Dyson DC40 Animal Ball-Technology Upright Vacuum Cleaner

Fantom Thunder vacuum whistled and stopped running and won't run now. Can it be fixed?

... Vacuums

My Dyson D23 Vacuum just stopped and it won't turn on no noise nothing stopped completely now what any suggestions?

... Dyson DC23 Bagless Canister Cyclonic Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0873 seconds