Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Stops just got dyson 07 off ebay and it only goes for couple of minutes then stops.

Answers :

You're walking too far from the outlet so the plug keeps getting pulled out of the wall
The heat sink - a small round piece of metal- on the overheating sensor has be come loose. Therefore safety cut out prematurely opens. This sensor is situated in the motor housing.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Stops just got dyson 07 off ebay and it only goes for couple of minutes then stops.

You're walking too far from the outlet so the plug keeps getting pulled out of the wall ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.

How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

Nutone central vac stops after a couple minutes then after a couple of minutes will start again

... Broan-NuTone Vx1000c Bagless Central System Vacuum

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)

Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roomba 4270 stops too soon. my roomba got weird all of a sudden. it started not moving all over as it should. so I tore it all down as I had done before and cleaned all the hair and dirt out of every thing I could without getting down to the basic shell. it does work now and does move all over but stops after about 10 minutes. brand new battery so not a battery issue. could I have plugged some of the sensors in the wrong 'plug'

... iRobot Roomba 560 Robotic Vacuum

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand

My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Dyson My Dyson vacuum runs for a while and then quits. If I wait a few minutes it will start back up. This just started doing this a couple of weeks ago.

The automatic cut out switch on the motor needs replacing when the motor gets hot this switch comes in and stops the motor from overheating when the motor cools down the cleaner will work again and cut out again when the motor gets hot if it is not r ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.

Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson 28 animal. When I start the vacuum the roller spins for a couple of seconds the stops. I have to turn machine off and on again then the roller will work for another couple of seconds.

... Dyson DC28 Animal Bagless Upright Vacuum

Help Hi I have had my irobot roomba model 4000 now for 3 months now, I just LOVE it sooo much. I have used it everyday since I got it. But now it is not working. I cleaned it all out I even sprayed it with that air spray can. What happens is, It starts to go then it acts like there is something in the way and stops then goes the other way, then goes off. What is wrong? Please help!!!

I had the same kind of problem with my model 400 today...after starting it and having it go in a circle for 30 seconds or so it would finally run into something and then back up a few inches, turn, then go forward a few inches, then back up a few inc ... iRobot Roomba 4210 Bagless Robotic Vacuum

My Dyson DC07 stops working after a few minutes. It works again after a further 10 minutes and then cuts out again. I have cleaned the filter and checked for blockages but is still cutting out. Can anyone help?

Have you tried calling Dyson? I had a problem with my Animal, and their tech department talked me though the fix. Worth trying them first. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Stopped working a few weeks ago - bought and installed new battery seemed to be working OK - now after about a week, it goes for about 15 minutes then stops...

It may need a longer charging period to bring the battery up to full charge. If you have a voltmeter, measure the battery voltage while it is being charged--it should read several volts above the rated battery voltage. If nearly equal, the charge uni ... iRobot 4150 Roomba Vacuum

Roomba goes a few minutes after a charge then stops

You can try cleaning the battery and charging contacts with some rubbing alcohol or contact cleaner, but its also possible the battery has reached the end of its service life. ... iRobot Roomba 560 Robotic Vacuum

I have a bissell proheat complete 2x. When I press the trigger to spray the water, it sprays for a couple of seconds and then the pressure drops and stops spraying. I turn turn it off for about a minute, turn it back on and does the same thing again. Jose Cortez

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Dyson Animal turns the "flipper"(?) on that I would use on my carpet, but it turns stops turning right away. It then goes on and off every 5 seconds or so.

You need to replace the belt that turns the brush. Here is the belt you need and a manual with instructions on how to change it:Dyson DC07 Belt and Manu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?

... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

My Animal Dyson (the purple one) is making strange noises. The ball will not roll. I've taken it apart and put back together and it works for a couple minutes and then it won't work again I think it's Model DC24 or 25. Pretty sure its 24.

... Dyson Ball DC24 Bagless Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

I cleaned the roller on my Dyson DC 07, and after reassembly, it makes a sound like the belt is being chewed. I took it apart a couple times, goes back together fine, but still makes the noise

Hi its Darran at Dyson. \012\012Your machine is designed to make this ratchet noise if the brush bar is \012obstructed. We would recommend checking the brush bar and soleplate \012area and removing any blockages or hairs/threads that are ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f

I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance

As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair  ... Dyson DC05 Bagless Canister Cyclonic Vacuum

A large screw got sucked up the vacuum. Since then the motor,which I replaced probably only 12 months ago, sounds very "winey" and when you stand the dyson upright the front brush still keeps going round instead of stopping. Any ideas? David

Sounds like the clutch mechanism has somehow been damaged.\015\012\015\012Have a look at the following site which is a great source of info on faults, dismantling, repairing and re-assembling:\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Shark only steams for a couple of minutes and then it stops

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I changed the motor in my Dyson Animal hoover and works fine but after 15 minutes it stops as if it was turned off, if i leave it for a period (2 hrs)it will start up again and work for a further 15 mins before shutting down.

Hi thereAll Dyson vacuum cleaners are fitted with a thermal cutout, which will switch off the motor if it becomes too hot. This is normally caused by a lack of airflow to the motor, i.e caused by a blockage or a dirty filter. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0557 seconds