Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

How to fit a new drive belt - Dyson DC07 Bagless Upright Cyclonic Vacuum


Answers :

Hi,
\015\012
\015\012There are different models of DC07 and the guide below is for the "standard" model. There are some slight variations on different DC07 models, but this should be more or less the same for all of them.
\015\012
\015\012
\015\012Disconnect the power and allow to cool for at least an hour before replacing the belt.
\015\012
\015\012
\015\0121. Sit on a chair, turn the vacuum upside down and hold it between your knees:
\015\012
\015\012belectric_33.jpg\015\012
\015\012
\015\0122. Undo the 3 fasteners at the positions shown in the picture below on the underside of the dyson (use a coin). Pivot the back edge of the sole plate upwards and lift off the sole plate which covers the brush bar:
\015\012
\015\012belectric_34.jpgbelectric_35.jpg\015\012
\015\012
\015\0123. Check for any debris arounf the brushes and the the spindle
\015\012
\015\0124. If the old belt is still intact, slide the belt off the motor spindle first. Then pull the brushbar upwards and away from the base of vacuum. Make note of how the old belt feeds through the hole and how the brushbar was correctly inserted.
\015\012
\015\012
\015\012belectric_36.jpg\015\012
\015\012
\015\0125. Remove the old belt from the brushbar and loop the new one over. Feed the new belt back through the hole and re-insert the brushbar.
\015\012
\015\012Make sure the plastic tabs on the end of the brushbar fit back into the slots correctly and the end caps are in place:
\015\012
\015\012belectric_37.jpg\015\012
\015\012
\015\0126. Loop the open end of the belt over your thumb, twist 90 degrees, the stretch the belt over the motor spindle untwisting it as you hook it over. It is easier to hook your fingers over the back of the hoover (see picture) to give you extra leverage when stretching the belt. After hooking the belt over the spindle, check to make sure the belt is straight and there are no twists.
\015\012
\015\012(Some people find it easier to stretch the new belt over the spindle before fully re-inserting the brush-bar)
\015\012
\015\012belectric_38.jpgbelectric_39.jpg\015\012
\015\012
\015\0127a If you hooked the belt over the motor spindle before full re-inserting the brushbar, re-insert the brushbar now (as described in step 5)
\015\012
\015\0127b Re-attach the sole plate - Insert the 3 plastic tabs on the inside of the rubber bumper at the front of the vacuum and pivot it downwards back into place. Tighten the 3 fasteners again using a coin.
\015\012
\015\012
\015\012belectric_40.jpgbelectric_41.jpg\015\012
\015\012
\015\012
\015\012This should be everything you need to know to replace the belt in your DC07. Please post back if you have any difficulty replacing the belt or need further assistance.
\015\012
\015\012Regards,
\015\012BElectric
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to fit a new drive belt - Dyson DC07 Bagless Upright Cyclonic Vacuum


Hi,\015\012\015\012There are different models of DC07 and the guide below is for the "standard" model. There are some slight variations on different DC07 models, but this should be more or less the same for all of them.\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hopw to fit new belt - Dyson DC07 Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to replace drive belt on a Dyson DCO7 - Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum


... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

I want to fit belt to DC07 how do i do it ? - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi there Jimmy, \012I have made a video showing exactly how to fit a belt to a dc07 vacuum cleaner. The video act ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cant get new belt on - Dyson DC07 Bagless Upright Cyclonic Vacuum


Yes, it's a real challenge! You can't help thinking something's going to break, but it will go on. For illustrated guidance, go to www.dysonmedic.com then scroll to the bottom of the page and click on "DC07 belt and brushroll replacement guide".\015\ ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Removal of drive belt on dc 07 full kit - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to put new cable on dyson dc07 upright - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Have a look at www.dysonmedic.com which has some excellent info on your machine. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Change belt on dyson dc07 animal - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do i fit forward lock on dyson dc07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

How to fix a new power cable to a Dyson DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


Try this site: http://www.sparesaver.com/help-and-support/dyson-sec ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do i fit forward lock on dyson dc07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Replace belt for dyson upright - Dyson DC07 Bagless Upright Cyclonic Vacuum


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do you change a belt on a dyson DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


Turn vacuum over so you can see the brush.\015\012Using a standard screwdriver, undo the three fasteners just behind the brush.\015\012Remove the base plate.\015\012Remove the belt.\015\012Remove roller brush.\015\012Pla ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do I change belt on dyson DC07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to fit an air Freshner on a Dyson DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need to replace drive belt on dyson dc17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Here is a link to the belt you need and a manual you can view which has instructions: Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Fixing new Bushes in a Dyson Vaccuum - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to replace main drive belt on dyson dc03 - Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Replacing clutch drive belt dyson dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Chris,\015\012I am just trying to find an owners manual, but I can not find one anywhere. Your link did not work. Can you help with another link? ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need to change my fan belt on my dyson - Dyson DC07 Bagless Upright Cyclonic Vacuum


You can get the belts you need here:Belts for Dyson DC07 with Clutch System ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to change a hoover belt on a dyson - Dyson DC07 Full Gear Bagless Upright Cyclonic Vacuum


... Dyson DC07 Full Gear Bagless Upright Cyclonic Vacuum

How do you change a belt on a dyson 07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


You want this part.http://www.sparesaverusa.com/vacuum-spares/dyson/dc07/dyson-dc07-parts/belt-changing-tool-for-dyson.html ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do you change the belt on a dyson DC 07 - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt you ar ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

How to change brush belt on dco7 dyson - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


This depends on whether your DC07 has a brush control clutch or not. For excellent illustrated guidance go to www.dysonmedic.com and click on DC07. For belt change on a model without clutch click on "belt and brushroll". It's simple! For models with ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1645 seconds