Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

My brushbar isn't rotating but the belt and motor are fine - any suggestions please

Answers :

The brushbar needs to rotate in the end pieces that hold it onto the head. If the motor and belts are fine, your problem is the brushbar is seized on its shaft. To solve, remove the bottom plate. Then lift out the end of the brushbar opposite the belt, but do not remove the brushbar. Grab the bar with one hand and the end cap with the other and pull the end cap off. It just slides on the shaft. If the shaft comes with the cap, no problem. That means the opposite end cap came off the shaft. Clean the dust/lint out of there and then take a look at the other end for the same. Slide everything back together and the bar should now be free to rotate on the shaft. Reinstall the bottom plate and you are ready to go.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brushbar isn't rotating but the belt and motor are fine - any suggestions please

The brushbar needs to rotate in the end pieces that hold it onto the head. If the motor and belts are fine, your problem is the brushbar is seized on its shaft. To solve, remove the bottom plate. Then lift out the end of the brushbar opposite the ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell quicksteamer powerbrush steam cleaner. The power brush will not spin but the motor works to rotate it. I went to purchase a new belt but the guy told me the belt was fine? Any other suggestions?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please

... Vacuums

My Bissell 9200 is not even a year old and the motor which drives the dual rotating brushes at the front of machine does not rotate. Please note belts are intact and are in good condition. Motor is not functioning.

... Bissell Vacuums

Hi, The belt of our Dirt devil bagless vaccum broke and we got new belt and replaced it. Even after replacing the belt, the brush is not rotating. Any suggestions please ?

Did you check to see that the beater brush, the brush that the belt drives, is free of debris and moves freely?\015\012When they bind up they can cause the belt to break.\015\012Remove the beater brush just as you do when changing the belt and clean ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.

... Vacuums

I have a dyson hoover. up to last week it worked fine. now it will not hoover up bits!!! i have to keep taking the long attahcment off and using that instead which is not ideal!! hubby has checked underneath..all brushes seem to be rotating fine and its not the belt. any suggestions?

Check the inspection air tubes on the Dyson - you don't say what model this is - and each model does have air inspection tubes but can be different to each model - which can usually clog up with dirt/debris thus making the machine difficult to pick u ... Hoover Vacuums

My Janome My Excel 23x will not wind bobbins. I have disengaged the presser foot so the machine does not stitch, the motor sounds like it is working fine, but the pin the bobbin sits on is not turning. Can you please suggest any other steps I may have forgotten

... Vacuums

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!

You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!

Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums

I have a Euro-Pro Shark UV-204. The Vacuum turns on, motor sounds fine, and suction is as strong as ever. Still picks everything up in its path. However, the bristels on the bottom do not rotate around, the belt is not broken or loose. Is there something I'm missing?

... Euro-Pro Shark UV204SH Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brushbar not rotating but vacuum has suction - belt not broke

At the point where the shroud is around the drive belt of the motor there is a screw that has to be remeoved. It is accessible through a hole in the housing that is inset about 3 1/2 inches. Once this is removed along with the 2 screws at the base ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?

... Bissell 8910 ProHeat Clear View Upright Vacuum

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin

Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.

Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.

Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Bissell 3760-1 has stopped sucking in the roller portion. The grab n go part are working fine. Checked the belt and it looks fine. Did I burn up the motor or a microchip?

Hey Lisa! Sorry you're having difficulty with your Lift-Off vacuum. Here's a link to troubleshooting steps to assist you with the suction.\015\012http: ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0920 seconds