Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Vacuum was just cleaned, filters everything, and still not getting good suction in upright postition. Is the beater bar adjustable?


Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacuum was just cleaned, filters everything, and still not getting good suction in upright postition. Is the beater bar adjustable?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.


Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson upright is not picking up like it used to. The suction from the tools is very strong and the beater bar is turning and clean. Please help


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri


Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kenmore progressive upright (direct drive) with bag has low suction and the beater bar does not rotate. Also, it is not obvious how to get inside the vacuum


Hi there,\012First of all you look for a reset button on the motor and press it in with cleaner plugged in and turned on, push the little reset button on the side of the lower base of vacuum. Remember that the brush will not turn in the u ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet


Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Help i can get suction from the hose but when i stick it in the back of the carpet head i get no suction and the beater bar will not turn. can you help


... Miele S184 Powerhouse Bagged Upright Vacuum

The vacuum does not have suction from the beater bar. The wand has good suction and the belt is still in place on the bar. There are no apparent clogs. What could be the problem


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Bissell cleanview is NOT suctioning well, all filters, nozzles, attachements, canisters and belts are clean and in good repair. We've pretty much made sure everything that I can get to without completely dismantling the vacuum is super clean and/or new... still poor suction


Did u check the filter above the dirt cup?\015\012\015\012twist the yellow piece and wash the filter ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Dyson dc7 quits after a few minutes running; runs again after an hour or two of rest. Filters are clean, beater bar is clean, can't tell about the airways because I can't see how to get to them.


Check the ducts with a small object(screw or something with a little weight)down the ducts to verify they are clean. Also check the Ubend on the back bottom of the unit. Looks just like a U. Remove with a turn of the tab by a screwdriver or quarter ... Vacuums

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum

Beater bar won't work. Have done all checks in manual. Bar is clean, belt seems to be connected properly and in good shape. Any ideas? John Rike [email protected]


Hi, I would have to say, that if the roller-brush Is clean and the belt is on and in good shape, that the problem will be in the vacs motor assembly itself. If the motor comes on, the beater bar will engage and pick up debris.If it is coming on and n ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Have an old upright that does not pickup dirt. The beater bar runs but the suction motor doesn't. Do not know how to disasemble upright.


I don't recommend taking it apart yourself. The problem could be a switch, wiring, or connection. The motor could also be bad. I strongly recommend taking it to an authorized Aerus Electrolux store for a free diagnosis. Let a trained service tech ... Electrolux EL5010A Bagged Upright Vacuum

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?


Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

I have a Kenmore Progressive Inteleclean Upright vacuum cleaner (with Bag) . It has good suction only through the hose now and none through the bottom for cleaning carpets. and, there is a noise like it has a suction leak. the brush is rotating.


Theres a little bendable neck that hose with suction plugs into. Thats the one thats clogged. You will have to fish it out by taking off the roller and clearing the clog. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Dyson Animal motor is running, beater bar is turning but very little if any suction. No suction from hose either. The inside canister is filling and moving, so there is some dirt being sucked in there. I have thoroughly cleaned all filters but not sure what is causing the problem. Any ideas?


Obstruction in the hose?\015\012Your vac has developed a hairball possibly.... when a piece of flexible media ie.... cardboard, plastic etc... gets lodged in the hose, and begins collecting hair & dust to the point it no longer has enough d ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?


... Bissell Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a windtunnel bagless 27.0 upright. there has never been good suction when the hosE and attachmnts are used. its as if the dirt is still working to clean up the dirt. is there something i can do? the hose is good.


Check this procedure like a reference guide about how to repair a Vacuum Cleaner...Vacuum cleaners typically last 8 to 12 years, depending on their quality, frequency of use, and general maintenance. By maintaining and repairing your vacu ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0996 seconds