Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Beater bar does not work dyson DC07

\015 It just stopped working,bad no sound. I have cleaned the filter and the brush and nothing is stuck. i still cannot get it to work. What now?\015

Answers :

If the beater bar does not spin freely, and the belt still seems to be in place, then you may not need a new clutch, but you may need to reset the clutch.  This is done very simply by keeping the beater bar section of the vacuum flat on the floor and reclining the handle all the way to the floor so the entire vacuum lays flat. There is a mechanism in the vacuum which resets the clutch. You will probably not hear anything when the clutch resets.  I sat on the phone for an hour and a half to hear this simple technique is built into the vacuum, but excluded from all instructions and website customer service information.
I thought the same thing with my dc07 and found out the hard way that if the unit is locked in th upright position than the bar turns off and wen you pull the handle back the bar spins
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater bar not working. suction not working - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Check for a broken beater brush belt.\015\012Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle.\015\012Reassemble making sure the belt is ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dyson animal beater bar not working - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Is the belt ok that drives it , is the clutch ok this video will give you instructions how to fix ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

BEATER BAR QUIT WORKING ON DYSON DC07 VACUUM CLEANER - DIDN'T KNOW IF THERE WAS A RE-SET SWITCH OR HOW TO GET THIS TO WORK AGAIN


Hi its Darran at Dyson. From your description of the problem, either the brush control has been switched off (dial on the side of the cleanerhead) or the belt has snapped which may indicate a problem with the clutch. Please ca ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater bar does not work dyson DC07


If the beater bar does not spin freely, and the belt still seems to be in place, then you may not need a new clutch, but you may need to reset the clutch.  This is done very simply by keeping the beater bar section of the vacuum flat on the floo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater bar won't work - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.


Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Is there any way to unfreeze the beater bar on a dyson dc07


... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Have a dyson vacum and the beater bar stopped working. How do you fix the beater bar.


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming with my DC28 Animal and all fo a sudden the beater bar stopped working and NONE of the floor mode buttons work.. no lights or anyhting. I checked for obstructions per the Dyson manua


... Dyson DC28 Animal Bagless Upright Vacuum

Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser


That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC14 dyson beater bar not working


Hi.\015\012\015\012Manuals for removing & replacing clutch are available from here,\015\012http://dysonmanuals.llc.nu\015\012\015\012If your in ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.


It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dc-15 bush bar will not work - Dyson 909592-05 DC-15 Roller Brush Beater Bar


Head motor blown, will have to take it to your nearest good hoover repair centre should cost around 49 dyson will charge 73 ... Dyson 909592-05 DC-15 Roller Brush Beater Bar

Dyson vacum beater bar does not work - Dyson DC14 Bagless Upright Cyclonic Vacuum


DC14 have two drive ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Dyson dc41 beater bar not working


... Dyson Dc 41 Ball

Brand new dyson dc46 beater bar not working


... Vacuums

I was going to send my animal in for repairs but after waiting a week Dyson sent the wrong box. The beater bar only works intermittently and the thing roars.


Hi there,I am very sorry to hear you are having difficulty with your machine. I apologize for the error regarding your box. However, we would appreciate the opportunity to assist you further in this matter. Based on the details you provided, ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I HAVE A DYSON DC07 I HAVE CHECKED ALL HOSES AND PLASTIC ATTACHMENT SECTIONS , CANNOT FIND ANY BLOCKAGE ANYWHERE IN THE SYSTEM .THE BELT IS GOOD AND THE BEATER BAR IS ROTATING WELL , BUT THIS VACUUM WILL NOT PICK UP ANY THING. I DID NOTICE THAT THE HEPA LIFETIME FILTER IS BLACK AND NOT SURE IF IT CAN BE WASHED OR CLEANED. THANKS BOB!


I have just cleaned mine just a half an hour ago - SAME PROBLEM !!\015\012ok take the dust cylinder off the vacuum cleaner and take the plastic clear cylinder off - there is a clear clip one side and you might need a small knife to unclip other ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson vacuum beater bar takes a while to start working.


Hi there, \015\012SmartAlec from NelsonVacuums.com.au here. If there are no bad sounds or smells when you are engaging the bar then it is a sign that your belts are s ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do you fix the beater bar in a dyson vacum. Otherwise the vacum works fine.


Its either the belt or the roller switch. Most likely the belt. Go to lowe's and get the replacement belt.Remove the screws that hold the cover on the bottom of the vacuum and remove it. You will see the broken belt. pull it out of the va ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Beater bar on my Dyson DC07 is not moving. How can it be repaired?


Hi there, \012This is not an easy question to answer in text form. I have made a video to show you how tostrip apart the brush and clutch section of your ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dyson Slim DC 18 all floors has no suction from the beater bar, but works great from the hose.


Hi its Darran at Dyson.Its possible that the brush bar is not turning when you release the head into the vacuuming position. Please ensure you complete a full blockage procedure as per your user guide to see if this resolves the problem. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Have a Dyson DC07 vacuum. The beater bar won't turn. Belt is good.


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.Unfortunately one of th ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

The beater bar doesn't work - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


You need to replace the belts. Here are the belts you need:Dyson DC14 Belts ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0504 seconds