Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

The beater bar is not spinning.

\015 I have checked the clutch and it is fine. I need to find the 2nd belt. Can you tell me where it is located.\015

Answers :

The brushbar isn't supposed to spin when it on bare floor. It's to prevent dirt flying around. It only spins when it's switched to carpet.\015\012
\015\012 I was just having issues with there being not much suction when it was on the floor mode. I flipped it over and noticed the small clear hose was not attached well. The Dyson is pretty user friendly, so i just popped it back in and used a butter knife to carefully push the ribbing over the plastic notches.\015\012
\015\012I've had my Dyson for almost a year. We LOVE it! I hope it keeps up! 
Hi
\015\012
\015\012The second belt is fitted to the clutch it goes from the motor to clutch.
\015\012
\015\012Not sure how you checked clutch but didnt see 2 belts.
\015\012
\015\012You will need to strip machine down removing brush roller & brush roll housing then you can get at the clutch.
\015\012
\015\012http://dysonmanuals.llc.nu/
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Beater bar is no longer engaged. Caught a shirt and I pulled it out of the head. After removal, it would no longer spin when I put the vacum in the engage mode. How to reconnect the spinning of the beater bar in the head?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

Caught a string in the beater bar. Cleared it out but now the beater bar will not spin. The belts are intact. I had this problem before and I can not find the answer online that fixed it. It is not the belt.


Hi there,Sorry to hear you're having a problem with your DC07. Please note that the brushbar will never rotate when the cleaner is standing in the upright position, or if you've used the brush control to turn it off. If you ha ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dc28 beater bar does not spin


This link is for manual check belt is okhttp://media.dyson.com/downloads/US/floorcare/Manuals/dc28_opmanual_usa.pdf ... Dyson DC28 Animal Bagless Upright Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Beater bar is not spinning. Any suggestions?


Belt is either broken or two slack ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The beater bar won't spin


Even though the belt is intact it can still be stretched and if it is it won't turn the brush roll when it's on the carpet. Here is a link to the belt you need and to a manual you can view: ... Rainbow E series Canister Wet/Dry Vacuum

Our dyson beater bar won't spin.


You can also find more up-to-date info on www.dysonforums.com www.dysonmedic.co.uk and ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan


Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Low suction The beater bar still spins fine, but the suction seems low. I have cleaned all of the filters, but it is still too low to spin a lot of the attachments.


Hi Megan,I'm sorry to hear you're having difficulties with your DC17. If it doesn't seem to be picking up as well as usual, you may have a blockage somewhere in the machine. To check for this, please follow the steps shown in our online suppo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not spinning, seems to be stuck but when I manually spin it, it will start but will stop and go.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell powerforce turbo, and my beater bar is not spinning, i have checked fordebris in the bar itself, but it seems one of the sides is not circle and it is getting caught on its little hole it fits into... so my question is.. Is it supposed to be circle? instead of oval shaped?


Usually the bar is driven by a belt--it may have come off or snapped and is broke. ... Bissell Vacuums

Beater bar won't spin


Here's a video that we've recorded to help you with this exact problem. This particular design is not a great design by Hoover, especially the belt system. The way the belts are designed, most people have to replace them at least once a year if n ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Bissell proheat carpet cleaner beater bar is not spinning and smells like burning rubber


... Bissell Vacuums

Dyson Animal 07 beater bar not spinning - belt not broken


If your unit has a clutch it maybe that it is in the off position or the motor belt is broken your unit has to belts if its a clutched model  ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar is not spinning.


The brushbar isn't supposed to spin when it on bare floor. It's to prevent dirt flying around. It only spins when it's switched to carpet.\015\012\015\012 I was just having issues with there being not much suction when it was on the floor ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater bar not spinning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


That means that the belt has stretched or broken and it needs to be replaced. Here is a link the belt you need and the manual which has instructions:Dys ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The small belt that makes the beater bars spin broke. It is only two years old; repair shops tell me this involves replacing two belts because of some kind of clutch to the tune of $150! Is this possible to repair myself


A very easy replacement. The belts cost about £3 each. Yes, there are two belts and even if the clutch needed replacement, this is about £20 for clutch and both belts http://www.dysonpartsdirect.co.uk/dysonparts/dc07belts.shtml - this is ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson beater bar won't spin - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson. \012he first check is to ensure that the brush control dial is set to the correct centre position when the machnie is locked upright. When you release the head the dial should move forward to the on position and th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not spinning - Dyson Vacuums


Invest $20 in a replacement (see Amazon.com et alia); Dirt Devil beater bars have sorta-sealed bearings that burn out once wear puts enough particles in the works, and you'd have to replace and reseal bearings in there if you did get it open yourself ... Dyson Vacuums

No suction The beater bar is turning but the cyclone is not spinning.


Blocked somewhere check hoses ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Problem with small belt and beater bar spinning. Where to get replacement belt and what is it called model number. Thanks. Only 2 months old 5780-900 Hoover windtunnel cyclonic


Here you can get a package of the belts you need. Also here is a link to the manual:U5780-900 Belts\015\012\015\012\01 ... Vacuums

My beater bar will not spin when the handle is lowered? But there's suction thru the hose when the handles upright


I had the same problem. I read, earlier today, that one of the "problem solvers" called Dyson. Dyson suggested, with the Dyson upright and plugged in, on a carpet, toggle the "bare floor" / "carpet" knob from bare floor to carpet 5 times, then lay ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0276 seconds