Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Caught a string in the beater bar. Cleared it out but now the beater bar will not spin. The belts are intact. I had this problem before and I can not find the answer online that fixed it. It is not the belt.


Answers :

Hi there,

Sorry to hear you're having a problem with your DC07. Please note that the brushbar will never rotate when the cleaner is standing in the upright position, or if you've used the brush control to turn it off.

If you have the cleaner reclined in the vacuuming position with the brush control set to 'ON', and the brushbar will not rotate, please get in touch with us free on 08002980298 (UK), or 1866MYDYSON (US), so we can provide the assistance you need.

Kind regards,

Jack
Dyson Customer Service
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Caught a string in the beater bar. Cleared it out but now the beater bar will not spin. The belts are intact. I had this problem before and I can not find the answer online that fixed it. It is not the belt.


Hi there,Sorry to hear you're having a problem with your DC07. Please note that the brushbar will never rotate when the cleaner is standing in the upright position, or if you've used the brush control to turn it off. If you ha ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Possible broken belt - where do I find access to the belt. The beater bar does not rotate when i release the handle. I like this machine, but It is only 2 years old, the warranty has expired. And i must say, I am disappointed I am concerned that this article will end up in the landfill, adding one more problem for the environment.


As you do not say which type of vac ? but assume definately upright hoover/dyson or similar ? the actual belt is not difficult to renew on either model/s at this stage can only suggest you turn vac over to reveal the cover that houses the ro ... Vacuums

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.


I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't


If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Beater bar not moving. Is there a belt? My mom sucked up a sock and didn't know. So she kept vacumming and then smelled something rubbery burning. And then we found the sock and cleared it. Then the beater bar wouldn't move after that. How do I fix it.


Hello,The belt is broken or badly stretched and needs to be replaced. Here is a link to download a manual.Look for the "Download Manual" on the right side of page. Scroll down towards bottom of page and you'll see how to open it up to cha ... Eureka 4700A Maxima Bagless Upright Vacuum

Beater bar will not engage. belt ok, cannot find a clutch, what else?


\015\012One possible problem could be a worn clutch. I just had the same problem. Before buying a new clutch assembly, I took the out the clutch just to make sure I could do it (the link previously mentioned is great: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar does not turn. The belt is fine.


WAIT!!! Don't replace the entire clutch yet... I just had the same problem. Before buying a new clutch assembly, I took the out the clutch just to make sure I could do it (the link previously mentioned is great: ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

The vacuum does not have suction from the beater bar. The wand has good suction and the belt is still in place on the bar. There are no apparent clogs. What could be the problem


... Dyson DC07 Bagless Upright Cyclonic Vacuum

U8174-950 SAVVY BEATER BAR NOT TURNING HOW DO I REPLACE BELT OR FIX BELT AND WHERE IS CLOSE SUPPLYER IN EDMONTON ALBERTA


Take the screws out from the plate covering the brush roll, look for maybe 2 screws from the bottom to take out, then turn vac over, remove the Hoover emblem and remove the screw there, now the top will come off and you can get to the belt and brushr ... Hoover Vacuums

Where do i find the drive belt for the drive belt for the beater bar on the morphy richards 73310


Try to go to there website ... Vacuums

Problem with small belt and beater bar spinning. Where to get replacement belt and what is it called model number. Thanks. Only 2 months old 5780-900 Hoover windtunnel cyclonic


Here you can get a package of the belts you need. Also here is a link to the manual:U5780-900 Belts\015\012\015\012\01 ... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I HAVE A BRISSELL MODEL 8910 THE BEATER BAR IS NOT TRUNING THE BELT IS ON BUT DOESNOT SEEM TO HAVE ANYTHING WRONG WITH IT SO WHAT COULD THE PROBLEM BE


... Bissell 8910 ProHeat Clear View Upright Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I have a model B1500 vacuum. The vacuum would lug and stop and start if I lifted it off the rug. I changed the belt to the beater bar. That didn't help. I also noticed that the connection between the hose and wand heats up. How can I fix it?


I'm not exactly sure what make of vacuum this is -- a number of companies make a model b1500, so this may be a bit general. If the vacuum has an adjustment for the height of the carpet pile and you have it set too low, it will overload the brush and ... Vacuums

The beater bar makes a loud noise and something is cutting into on the end opposite of the belt. I have taken it apart and cannot find anything that appears to be out of place. Lynnette


Check to see if the belt is missing any gears. If it is then that is your problem. anothe issue might be that the roller bearing is loose or missing. you will be able to see this when you take off the bottom plate. let me know if this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I HAVE A DYSON DC07 I HAVE CHECKED ALL HOSES AND PLASTIC ATTACHMENT SECTIONS , CANNOT FIND ANY BLOCKAGE ANYWHERE IN THE SYSTEM .THE BELT IS GOOD AND THE BEATER BAR IS ROTATING WELL , BUT THIS VACUUM WILL NOT PICK UP ANY THING. I DID NOTICE THAT THE HEPA LIFETIME FILTER IS BLACK AND NOT SURE IF IT CAN BE WASHED OR CLEANED. THANKS BOB!


I have just cleaned mine just a half an hour ago - SAME PROBLEM !!\015\012ok take the dust cylinder off the vacuum cleaner and take the plastic clear cylinder off - there is a clear clip one side and you might need a small knife to unclip other ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need to change the belt on my kirby model 519, assuming this is the problem since the beater bar is not turning and I can smell burning rubber


The beater bar is jammed--usually from thread, string, and hair that is wound up on the bar and particularly on the bar end bearings. The bearings themselves usually require cleaning and re-oiling. The belt may be damaged sufficiently to require repl ... Vacuums

The beater brush on my Hoover windtunnel model u8174-900 won't revolve. The belt looks OK. How can I fix this problem?


Help wont pickup blows out ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Sebo Air Belt C3.1 Were hose enters handle, leaks air causing a high pitched whistling sound. How can I fix this. I have taken hose into shop, but they could not find a problem.


... Sebo Air Belt C3.1 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0658 seconds