Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dyson slim cannot remove switch cover

\015 I removed the back screws there are 4 and cannot remove. Cover so I can replace a new on and off switch help I have everything off but cover will not come ogg. Linda\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson slim cannot remove switch cover

Here is video for DC07 switch replacement,http://www.videojug.com/film/how-to-replace-a-dyson-switch-and-actuator-dc07 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work

It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o

Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How do you remove the switches housing cover on a Dyson DC25?

... Dyson DC25 Animal Bagless Upright Vacuum

I have the dyson dc07 all floors and have a new belt- I have removed the black cover but cannot see where to attach the new belt ! Hope you can help-Carole

Hi there Carole, VacuumGuru here. \015\012I have made a video on how to access the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How can i remove a switch cover to a dyson dc18

... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

How to remove dyson dc15 upright switch cover

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Removing the switch cover on a Dyson 25 animal vacuum

... Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth

When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Dyson Vacuum Cleaner On-Off Switch removal

... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

DYSON DC04 how to remove switch housing to check

Its most likely not the switch, check the power cord.. check where the cord meets to the vacuum. the cord could be going bad and most likely not a loose wire. ... Vacuums

Replacing the on/off switch on Dyson DC07. After the switch retaining screw is removed, how is the switch removed? Does it just pull out or are there retaining tabs ?

Have a look at www.dysonmedic.com which has some great info on your machine ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Removing on/off switch on dyson dc26

... Dyson DC26 Bagless Canister Cyclonic Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off

I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?

Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

I have a Dyson slim DC18 all floors, the power switch is bad it won't stay latched I would like to get 2 of the switches. Dyson 18 s/n 334-US- A 26163 Nelson LePla 5495 S.Fordney RD Hemlock MI 48626

You can order the switch from the following sites. According to the first site, the DC17 and DC18 switches have the same part number, so I'd use the second site. It costs less. I didn't check the shipping costs, though.\015\012 ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

My Sebo X1 stopped working and my husband tested it and determined that the on off switch was not working. I purchased a replacement switch online but I cannot figure out how to remove the old switch. Please can you help?

Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Sebo Automatic X1 Bagged Upright Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

My Sebo X1 stopped working and my husband tested it and determined that the on off switch was not working. I purchased a replacement switch online but I cannot figure out how to remove the old switch. Please can you help?

Www.manualnguide.com/manual/sebo-x1-repair/page/3/\015\012\015\012Above is your user manual, and below is an exploded diagram so you can see where it all goes. Find all the screws lock ... Sebo Automatic X1 Bagged Upright Vacuum

How do I remove switch housing on dyson dc18?

I have a similar problem and want to check the switches...the last release is not apparent...appreciate some help...[email protected] ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.

When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

Removing cover over beater bar for cleaning on dyson animal vacuum. Accidentally ran over mess on carpet and need to clean inside of cover and beater bar. Thanks

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


It is a snap lock plastic cap on mounted to the frame. ... Bissell 9200 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6501 seconds