Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

My vac cleaner doesn't pick up.

\015 Have replaced filters but still no suction\015

Answers :


There could be a few things that would cause your Dyson to have no suction. I will give you detailed step by step instructions along with pictures on how you can diagnose this.

Possible Problem #1. The first problem is extremely common. In fact, we probably see between 2-3 of these problems every week. It mostly happens after people take the bottom plate off the vacuum in order to clean the roller brush. What happens is when they reinstall the bottom plate, they put it on on incorrectly. It's actually very easy to do. When the bottom plate (soleplate) is installed wrong, there will be a gap between the bottom plate, and the agitator housing, or the purple tray the roller brush sits in. This will cause the soleplate to be a few inches higher off the ground then it should be, preventing the brushes from even hitting the carpet. This makes it seem to the user that vacuum has lost suction power because without the brushes hitting the carpet, the machine will not pick up very well on floors, but when they use the attachment hose there's plenty of suction power.

Here's a picture of the WRONG way to install the bottom plate. Notice the gap in between the two housings:

Here's another picture, that is the RIGHT way to install the soleplate:

I would say probably 6 times out of 10 this is the problem with the customers machine. If you checked the soleplate and it is installed correctly, move on to the second possible problem.

Possible Problem # 2. Turn the vacuum cleaner upside down so the brush roller is facing upwards. I found the easiest way to work on it is to put it on a counter top or work bench. On the left hand side behind the roller brush you should see a flexible transparent hose that goes from the motor to the agitator housing. This hose actually has a lot of strain on it when the vacuum cleaner is in the reclined position. When the first few series of Dyson DC07 models came out, they didn't make this hose long enough, so when the vacuum was in the reclined position, it would put too much stress on the hose, and cause the hose to actually crack, usually right where the end of the hose that goes into the agitator housing. Examine your hose and see if you have any visible cracks in this hose. If you need to you may just remove the entire hose assembly by pulling on it. It will easily come right out of the machine so you can inspect it better. Here's a picture of where the hose usually cracks:

This would also explain why the vacuum works fine when using the attachments, but not on the floors. The attachment hose uses a different suction channel, and when the machine is in the upright position, no suction goes through this hose. If you do find a crack in this hose, the this hose needs to be replaced. Here's a direct link to that hose on our GoVacuum website.
Dyson DC-07 & DC-14 Upright Replacement Internal Hose Part # 904219

Possible Problem #3. I would suspect that this may not be the problem, but if neither of the solutions above worked, then try this one. Dyson's in general are prone to clogging. There are a few clog ports throughout the vacuum cleaner that were added there due to Dyson prototypes becoming clogged at these points. Here are pictures of how and where to check for these clogs. Simply remove the suction port covers at both of these locations:



Possible Problem #4. If none of the above solutions worked for you, try this last one. The Dyson DC07 models use a clutch mechanism that stops the roller brush from spinning when changed from carpet mode to bare floor mode. This clutch mechanism is a notorious problem with all Dyson models, in fact they were such a problem that Dyson had to redesign the DC07 model to a non-clutch system. Even if yours is one of the newer ones that don't use a clutch, yours still has a belt inside. You can tell if your model uses a clutch or not by the shape of the roller brush. If your brush is a perfect cylinder shape, yours does NOT have a clutch. To check and see if the clutch or the belt have gone bad, first release the handle on the vacuum as if you were vacuuming carpets. Make sure the machine is set to carpet mode. Now while the handle has been released, turn the machine upside down and see if the brushes are spinning. If the brushes are spinning then turn the vacuum right side up and put the brushes on the floor. Can you still hear the brushes spinning when they are hitting the carpet? If yes, then this is not the problem. If the brushes however are NOT spinning, this indicates either your brush roll, clutch, or belt have gone bad.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My steam-vac carpet cleaner doesnt seem to be pulling the dirty water back out of the carpet.

The most common reason for this is that the lid is not fully seated on the dirty water tank. Be sure to hook the lid in front, and then snap it in place at the rear. Another problem could be that the duct is missing from the front of the tank. ... Hoover Vacuums

My vac cleaner doesn't pick up.

Hello,There could be a few things that would cause your Dyson to have no suction. I will give you detailed step by step instructions along with pictures on how you can diagnose this.Possible Problem #1. The first problem is extreme ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Doesnt pick up water - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Possible Causes Remedies\015\012 \015\012ReadyTools Dial may be at the wrong setting for the cleaning job <> Set ReadyTools <> Dial to either Tools / PreTreat ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??

If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My hoover steam cleaner will not pick up the water the machine pu

Two checks:\015\012(1) Is the lid aligned and sealed to the recovery tank\015\012(2) Is the round rubber gasket installed on the tubular post under the hood, where the tank seals to the base? The tube extending down from the tank must si ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm

I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?

That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How to change mini shop vac filter - Shop Vac Shop-Vac Hang Up Mini Canister Vacuum Cleaner Vacuum

... Shop Vac Shop-Vac Hang Up Mini Canister Vacuum Cleaner Vacuum

The vacuum cleaner does not pick up anything from carpet. It does not even pick up pieces of thread laying on carpet. On tile floors it blows dirt away instead of picking it up. I've tried all the settings on the brush and nothing works. It has done this since new

Sounds like there is a clog..\015\012\015\012Usually its in the hose - look closely.. Stretch the hose out straight and look in there good..\015\012\015\012Or a clog could be in the vac close to where the hose conects to the v ... Hoover U5269910 Bagless Upright Vacuum

Carpet cleaner won't pick up water - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?

Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent--is it clear? Check the interior hose that you ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

Bissell laminate floor cleaner wet vac and flips to dry vac

You just need to replace the cap and valve part # 2036919, You should be able to order the part thru Bissell.com, or they will tell you who you can call close to you. ... Vacuums

Homewell vacuum cleaner, bagless Model SKU3358 won't pick up via the floor brush. Seems to have plenty of suction in the hose. I have cleaner filters & checked there are no blockages.

... Vacuums

Hello I can not find my manual for my vax vs19 swift vacuum cleaner and I am having problems with the cleaner not picking up. It is a 1600w machine and is fitted with a hepa filter, my son took it apart and without the manual it is difficult to reassemble not sure if he has put it back together properly.

Check out this site;\015\012\015\012http://www.vax.co.uk/support/vacuum-cleaner-user-guides\015\012\015\012Scroll down to the one that's applicable. ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

My carpet cleaner doesnt **** up the water and cleaner it is a bissell turbo proheat 2x

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

The Dirt Devil Featherlite vacuum cleaner throws up the dirt back out. Sometimes the vacuum cleaner doesn't pick up any dirt

You have a blocked vacuum hose take hose off and out side. Push the garden hose from one end to the other, this will push out the blockage ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

I have the hoover automatic dual vac 5. this is the 3rd hoover rug cleaner i purchased and always the same problem the spray underneth the rotator bars hardly dispenses and the floor hardly gets wet, this has happened with all 3 rug cleaners

The carpet is not intended to get soaked, like what you see with a spray application. If you are seeing a stream of water in the nozzle/tank during the recovery stroke, this is working properly. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover carpet cleaner not picking up water - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My carpet cleaner will not pick up water. - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Check to make sure that the recovery tank lid is fastened down all of the way around. Also if the foam filter on the bottom of the tank lid, make sure there is at least a 1/4 inch gap from the top of the lid. The wire screen filter is plugged, from ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Merlin Automatic Inground Pool cleaner (onboard bag, no hoses)is no longer picking up debris. Bag is clean, it still moves across pool all seems as it should be -- EXCEPT he's not picking up the dirt!?

The belts need to be replaced ... Vacuums

My Steam Vac does not pick up the water from the carpet why? When I pull the Vac backwards to **** up the water it sucks it up sometimes and sometimes it doesn't Is there a manual I can get I seem to have misplaced mine.

Ebay,google,or the manufacturers website they usually have downloadable manuals... ... Hoover F5858-920 SteamVac Wet/Dry Vacuum

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!

I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

For the first time, I tried using my Kirby Sentria shampoo attachment. I've lost the manual but found instructions online for making the swap from regular vac to shampoo-er and got it all assembled. The foam laid down just fine, however, when I run the vac back over the foam to pick it up, there is not a stitch of water showing up in the tray. First I thought maybe it was bc I hadn't put that much of the foam/water onto the carpet, but 12 hours later, the carpet is still wet in spots. Clearly

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=638285\015\012Generic problem for all Vacuums\015\012For the first time, I\015\012Posted by MHicks on J ... Vacuums

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks

Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0782 seconds