Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

No suction when carpet cleaning. Also won't stand upright

\015 Suction coming from hose. Appears to be no suction from floor\015

Answers :

I had the same issue and solved it easily. When you push your foot onto the base and then recline the handle, use your toe to gently push the very front of the base down closer to the carpet. This creates a much stronger suction and picks up every bit of dirt easily. If i do not do this extra step the suction is much much less. I tried an experiment with sand that I poured onto my carpet. Initially, I went over the sand 4 times and the dyson 07 would only pick up 50 percent of the sand. I then poured more sand onto the carpet, and this time pushed the front lip down so it was contacting the carpet. This time only two passes were needed to completely **** up all the sand. Not sure why this is not in the manual but it really works. Good Luck!
The brush is not rotating, No strings are wrapped around the brush, I have checked all the hoses, The main hose has great suction, there is a little in the foot, but the brush will not move to pick up anything on carpet.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction when carpet cleaning. Also won't stand upright

I had the same issue and solved it easily. When you push your foot onto the base and then recline the handle, use your toe to gently push the very front of the base down closer to the carpet. This creates a much stronger suction and picks up every ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi...there is no suction in my upright's hose...there is suction when regular carpet cleaning but when I put it in an upright position and take the hose out there is extemely light suction.

... Miele S7210 Bagged Upright Vacuum

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond

Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

I removed the brush from bottom of the vacuum to remove hair from the bristles. When I re-assembled the vacuum, there was no longer suction. Also, the vacuum no longer stands upright when not in use. It's like something is blocking the upright portion from locking.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

The carpet cleaning portion of the vacuum sucks debris up poorly, and during the whole time I have it on carpet, the hose continues to have strong suction. The vacuum also spits out what its vacuumed up.

The screws along the base of the vacuum must be removed . The vacuum cleaner cover must then be removed exposing the suctioning hose syphoning the debris from brush roll area. Pull the hose from the brush roll area letting it hang freely. Remov ... Vacuums

I have a Kenmore Progressive Inteleclean Upright vacuum cleaner (with Bag) . It has good suction only through the hose now and none through the bottom for cleaning carpets. and, there is a noise like it has a suction leak. the brush is rotating.

Theres a little bendable neck that hose with suction plugs into. Thats the one thats clogged. You will have to fish it out by taking off the roller and clearing the clog. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The extension arm of my Dyson Animal no longer has any suction. I can attach it but it has extremely limited power to reach high places or under furniture. Also, when I stand the unit, used as vacuum, upright and the top valve opens, there is a strange noise that wasn't present when I first purchased.

You have a blockage within the wand or at the u-bend at bottom of the hose....try removing wand and see if u hav esuction at end of hose...if so wand is blocked,if not removed u-bend ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?

Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums


The hose is clogged or the belt is broken ... Vacuums

No suction I have a bissell turbo heat upright carpet cleaner. I've used it once and loved it. I cleaned one room today and realized it wasn't sucking up the water and is louder than before. Please help.

If this is a 9400 series check and make sure the red flap in the lid of the dirty water tank is not closed. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri

Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Electrolux el8807 has no suction - Electrolux EL8807A Precision BrushRoll Clean. Bagless Upright Sealed HEPA Vacuum Cleaner 13"W, Wash Filter, Floors Carpets, 12A, 12Hose, 24Cord 15Lb

... Electrolux EL8807A Precision BrushRoll Clean. Bagless Upright Sealed HEPA Vacuum Cleaner 13"W, Wash Filter, Floors Carpets, 12A, 12Hose, 24Cord 15Lb

Shuts off at upright position also has lost suction. I have already cleaned the filter

Check for a clog ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

S7000 my miele upright vaccum cleaner looses it suction when on carpet mode, suction is perfect when upright (hose). The suction lasts for appox 5 mins when on the carpet and it stops.

... Miele Vacuums

Suction loss when handle is tipped back to clean carpet

Ours did the same thing. I cleaned the filter and canister thoroughly. It needed to be cleaned, but that didn't fix the problem. I removed the plate under the carpet brush bar (three quarter-turn screws) and removed all hair, lint and threads from th ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell aroma pro upright carpet cleaner wont push foward keeps getting stuck

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet

Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene

... Vacuums

No suction my riccar 8850 has no suction. I cant find any clogs and there is some suction on the hose when using cleaning tools but when hooked up to the vaccum bag it wont clean

Replace your belt. Remove the baseplate, remove the brushroll, place a new belt around the motor pulley, then around the pulley on the brushroll, and pull the brushroll back into place in the nozzle. Spin it by hand to make sure it spins, (otherwise ... Riccar 8850 Vacuum

The suction for carpet cleaning is great but there is very little suction through the hose. I have cleaned out the hose but there is still very little suction. What else can I do?

Have you tried cleaning the hose from the vacuum end, the end that feeds the sweepings into the cannister/bag? Might be something close to that end of the hose.\015\012Also, one reason for a hose not to work is the possibility of a cut or broken hos ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?

The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0837 seconds