Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dyson dc07 makes loud noise when on carpet setting bar does not spin, could clutch need replacing?

\015 Still works on bare floor setting. Beater bar is intact and moves as it should. Took vacuum apart to that point. Belt that is visible also seems intact.\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc07 makes loud noise when on carpet setting bar does not spin, could clutch need replacing?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???


The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

The small belt that makes the beater bars spin broke. It is only two years old; repair shops tell me this involves replacing two belts because of some kind of clutch to the tune of $150! Is this possible to repair myself


A very easy replacement. The belts cost about £3 each. Yes, there are two belts and even if the clutch needed replacement, this is about £20 for clutch and both belts http://www.dysonpartsdirect.co.uk/dysonparts/dc07belts.shtml - this is ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?


Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

My brush roller stopped spinning so I had to take it off and clean out all the hair that had gotten wound around it. I replaces it and now it is make a lound noise, but only when the brush is on. Could it be the belt making such a loud sound? It wasn't making this noise before.


Could very well be the belt.\015\012When cleaning the brush it is a good idea to add some WD40 at the ends where the plastic pieces are that hold the brush in the vacuum. The brush needs to be able to move freely around the plastic pieces.\015\012Ad ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon


... Riccar Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

I cannot seem to replace the beater bar on my Dyson - it seems to spin OK, but when I turn the vacuum back on and turn it to the 'Carpet" position, it makes a noise that is unbelievable. What's up with that? The belt is intact.


Sounds like its the clutch to me if it sounds like a rapid clicking and you have a large knob on the side of the cleaner head it is going to be the clutch this is a hard part to changed without the know how to do it and it is very easy to break the o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

I just put a new belt on my boss 4800 and it is to loose? Does the beater bar needed to be replaced? There is no traction to turn the belt, it spins


Sounds like the belt is to big you didnt replace with the correct belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym


Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.


Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Is it possible to remove the brush bar from the housing of a mieleTurbobrush STB 205? The brush bar is not spinning due to been dirty and clogged and needs to be removed for cleaning. Is it possible to remove the brush bar????


... Miele 06271980 STB 205-3 Turbobrush
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0999 seconds