Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dyson DC07 Vaccum - brush will not turn

\015 I loaned my Dyson to a friend with hardwood floors. They switched the brush off. I got the vacuum back and switched it back on. They will not turn. There was a clicking/grinding noise --- and some foul smell like something was burning. The belt is not broken and the brush will turn easily enough by hand - but the vacuum will not engage the brush anymore. It is useless to me as I have carpeted floors. Can anyone help?\015

Answers :

Hi.
\015\012
\015\012Your Dyson has A clutch unit this engages the brush roller when you pull the handle back to vacuum.

Check the clutch control knob which is at the bottom left side of machine looking from the front.
It should rotate to drive position when handle is pulled back.

If it doesnt turn the knob by hand to drive & try the machine.

If you still have no brush rotation after doing all this then UNPLUG machine from mains supply.
\015\012Now lay machine on its side & remove the sole plate, This is the cover over the brush roller.
\015\012Turn the 3 plastic screws to unlock postition & lift sole plate off.
\015\012
\015\012Now try to yurn brush roller using your hand. It should turn freely if it is difficult to turn look for any foriegn object obstructing the roller.
\015\012
\015\012If no obstruction found then remove the brush roller from the machine & check the bearings in the ends of the brush roller one or both may be siezed up if they are then new brush roller will solve the problem.
\015\012
\015\012If bearings are good then either the clutch is faulty or the second belt which goes clutch to motor has snapped & will need replacing.
\015\012
\015\012It is difficult to fully explain the clutch removing procedure,
But there are service manuals available for these repairs at this site
http://dysonmanuals.llc.nu/
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson DC07 Vaccum - brush will not turn


Hi.\015\012\015\012Your Dyson has A clutch unit this engages the brush roller when you pull the handle back to vacuum.Check the clutch control knob which is at the bottom left side of machine looking from the front. It s ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Roller brush of my dyson dc07 isn't turning...


It migh be the belt.check your belt or it is the brushroll is stuck.(from to much hair ect.) ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush won't turn on dyson dc07


There was a belt that was to be attached to the motor shaft under the belt cover, be sure that it didn't pop off. the recommended fix is to replace the clutch, not the belts in the clutch. if you only replaced the belts it could still be a bad clutch ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson Animal handheld brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson.We would recommend checking it for a blockage and a removing any hair or fibres from the brush bar. As the brush bar relies on the suction power of your machine, it would be worth cleaning the filter and ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi my dyson dc07 animal has suction but the brush bar wont turn. If I turn it on there is a horrible noise. The belt is still fine


The belt is probably worn or stretched. When this happens the belt won't turn\015\012the roller brush when it is against the carpet. Here is a link for the\015\012manual and links for the belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC07 brush does not turn - belt intact - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi there, The problem is likely to be \012a) The selector on the front of your machine is set to hard floors\012b) The ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 switched off whilst hoovering, It would not turn on, 1st it stopped rotating brush and than tuned off completly.. I tried ttoi change the fuse but still not turn on. Motor not runnung either.


Hi its Darran at Dyson.Our machines are fitted with a thermal cutout switch. This will activate if the motor on your machine becomes too hot. This is caused by a lack of airflow to the motor, which is caused by a dirty filter or a blockag ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.


Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


That is usually caused by a worn, stretched or broken drive belt. Here is a link to the replacement belts you need and to a manual that you can view which has instructions. It's really simple. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Is the motor operating when switched to "on " position? Is so I would have to assume that the belt is broken to the power brush /head. Did you happen to smell burning rubber at all when the brushes stopped working? Look in your manual for replaci ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush won't turn - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


\015\012\015\012Belt is broken. You will need to re[lace the clutch. Here is a video on how to do that. ht ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roller brush does not turn when vacum is on - Dyson DC07 Bagless Upright Cyclonic Vacuum


The belt is broken or stretched. You can get replacement belts for the DC07 here:Belt for DC07 with clutch ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson i got a free dc07 animal but the brush doesnt turn it appears the belt is still on it but i cant see how to get at the belt


Hi.\015\012\015\012There are 2 belts the one is hidden under the Black casing.\015\012\015\012If you require help got to this site http://dysonmanu ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes do not turn - Dyson DC07 Bagless Upright Cyclonic Vacuum


If the brushes do not turn you need to change the belt. to do this under the machine where the brush is there should be flat slots you can unclip to get the panel off by the brushes when this is off you should be able to see and access the belt hope ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson Aminal Vacuum simply will not turn on. I plugged it in this morning, pressed the power button- and nothing. No warning sounds, simply silence. Sigh. Nothing is wrong with the wall outlet.The vaccum is 3 years old but has run perfectly until this point. The brushes are clean of any accumulated hair. What part might need replacing?


The power switch may need to be replaced. Call the Dyson helpline - they will give you the location of an authorized Dyson dealer in your area who will be able to replace the switch. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Belt could be worn, brushroll bearings could have gone. Even the clutch could be broken.Is the brushroll jammed? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes won't turn but vacume runs - Dyson DC07 Bagless Upright Cyclonic Vacuum


I suggest you check the drive belt, located under a cover on the bottom of the unit. It may appear to be good (tight and not worn) but 9 times out of 10 that is the problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush is not turning - Dyson DC07 Bagless Upright Cyclonic Vacuum


Remove the bottom brush cover and replace the belt. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush doesn't turn and belt apears good - Dyson DC07 Bagless Upright Cyclonic Vacuum


If your unit has a large knob on the right side of the cleaner head as you hold it when cleaning then your unit has a clutch this clutch has two belts in it so the brush belt may appear ok but the motor belt might be broken it is not an easy repaer ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush bar on my dyson dc07 will not turn.


Hi.Your Dc07 may have A clutch unit.Check that when you pull back handle to vacuum that the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park position. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush quit turning while i was vacuuming - Dyson DC07 Bagless Upright Cyclonic Vacuum


Could be some debris is caught in brush or belt broke. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes do not turn - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


HI there, \012There are a couple of reasons that your brushes may not spin. \0121. The hard floor / carpet dial is set to hard floor. \0122. The clutch to motor belt is broken\0123. The clutch to brush belt is broken.\01 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0573 seconds